Interested to Buy Any Domain ? << Click Here >> for more details...
difference between a four point starter and three point
starter
- 9 Answers
- 79012 Views
- I also Faced
- E-Mail Answers
Answer Posted / jasif farooq pala
Your Answerthe basic difference between in the circuit of 4 point stater as compared to 3 point stater is that, the holding coil is removed from shunt felid circuit and us directly connected across the line with a current limiting resistance R in series
| Is This Answer Correct ? | 0 Yes | 1 No |
Post New Answer View All Answers
Is vtg is controlled by the resistor? if else how much?
what is magnetizing current test in power transformer
i will applied in 1U-1W on 440 volt primary delta side. what is the result of magtic balance test
i need previous entrence exam papers of nhpc.
HELLO EVERYONE, I RECENTLY HAVE FOUND ONE PROBLEM, I WAS TAKING NO LOAD TRIAL OF AN HT MOTOR 920 MOTOR , 1440 RPM , 6.6 KV, WITH AUTO TRANSFORMER. AT 450 V, LOAD WAS 40 AMP AND SPEED WAS 250 RPM. BUT AS WE INCREASE VOLTAGE FROM 450 TO 480V, LOAD BECOME 41 AND SPEED REDUCED TO SOME RPM . SO WHICH PHENOMENON ACTED HERE FOR REDUCING SPEED.?? AND IS IT HAPPENING ALWAYS OR IT IS RARE? I ALSO HAVE FACED SUCH PROBLEM WITH FEW LT MOTOR ALSO.
What is an automatic controller?
IN MY SYSTEM THERE IS ONLY OVER CURRENT EARTH FAULT RELAY IS AVAILABLE. FOR THE UNBALANCE SENSING IS THERE ANY RELAY IS AVAILABLE? THE SAME CTs WHICH ARE USED FOR THE OVER CURRENT EARTH FAULT RELAY CAN USE FOR UNBALANCE ALSO?
how to calculate the power factor when instantaneous voltage and current has harmonics in it ?
Dear all, I want to use Induction motor to open and close a 1 ton door. How much power do I need. Thanks
how many single tension hardware are required on a double circuit transmission tower?
what r the safety measures in UPS ? explain all?
How can we choose the rating of submersible motors
why 5kW motor becomes unbalance if its relay trip 1st time and its set value is 7.0 A
Difference between megger test equipment and contact resistance meter test instruments?
Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1. H1-H2 = H2-H3 H3-H1 2. H2-H3 = H3-H1 H1-H2 3. H3-H1 = H1-H2 H2-H3 For the LV side also: 4. X1-X0 = X2-X0 X3-X0 5. X2-X0 = X3-X0 X1-X0 6. X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0 H2-H0 H3-H0 X0-X1 X0-X2 X0-X3 128.0 119.9 7.2 29.2 13.3 15.8 70.7 128.4 59.2 23.4 22.0 3.6 7.2 120.1 128.1 13.4 29.3 15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone?
