Heat transfer: In a steady state one dimensional conduction with no heat generation, the differential equation is d / dx (k dT / dx) = 0. Prove that T(x) = ax b, where k, a and b are constants. (b) At x = 0, T = c and at x = L, T = d. Prove that T(x) = (d - c) x / L c for boundary conditions.
- 1 Answers
- 1827 Views
- I also Faced
- E-Mail Answers
Answer Posted / kangchuentat
HEAT TRANSFER - ANSWER 5.2 : When d / dx (k dT / dx) = 0, d (dT) / [ (dx) (dx) ] = 0. Integrate both sides gives dT / dx = a. Second integration gives T(x) = ax + b for both sides (proven). (b) T(0) = a(0) + b = b = c. T(L) = d = aL + c then a = (d - c) / L. Substitute in T(x) = ax + b gives T(x) = (d - c) x / L + c (proven). The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
What is the Import Procurement Cycle ? and what are the customization steps in SAP ?
X is strong but has a very low density (1% of traditional earth materials.) and hence light weight. It is a recyclable material. The compression behaviour of X is strain rate dependent. Higher strain rates result in higher initial modulus and higher compression strength. It can also withstand unlimited number of cycling loading provided the repetitive loads are kept below 80% of the compressive strength. The internal structure of the material includes air-traps which make it poor heat conductor. X is non- biodegradable and chemically inert in both soil and water. Most acids and their water solutions do not attack it; however strong oxidizing acids do. Solvents which attack X include esters, ketones, ethers, aromatic and aliphatic hydrocarbons and their emulsions, among others. It does not support bacterial/fungal growth as well .It also has significant acoustic properties and effectively reduces the transmission of airborne sound. X is combustible and should not be exposed to open flame or other ignition sources. Combustion products are carbon monoxide, carbon dioxide, water and soot. Long-term exposure to sunlight causes yellowing and a slight embrittlement of the surface due to ultraviolet light. X is able to withstand the rigours of temperature cycling, assuring long-term performance.
What are the design considerations for a piping system for the transfer of slurries?
What are the some common causes of control valve noise?
What are the apt definitions for apparent power, active power and reactive power? Explain about different types of lamps?
What is a "saltation velocity"?
At what temperature is glass fused to steel in the making of glass-lined equipment?
MY generator water cooler inlet line height - 11 mtr inlet water line height - 7 mtr water come into the line from overhead tank, O/H tank height - 20 mtr the first tapping in the inlet line is 2" line which down to 4 mtr level plateform., second tapping in inlet water line goes to a pump 6" line installed at 4 mtr level plateform, pump capacity 200m3/hr, head- 30 mtr, hp-40. the outlet of pump of 6" water line connected to a header of 6 mtr long of 6" line, on this header the six tapping are connected, 4 nos. 3" line goes to 11 mtr height water cooler the pressure of the line is 0.15 to 0.25 kg/cm2, 2" and 4" pipe line connected to a cooler at 4 mtrlevel plateform. my question is, at 11 mtr height level the quantity of water and flow is not sufficient for my cooler, the temp. of cooler is rises much more. you are requested to suggest the modification of pipe line/ pump for take more water flow and pressure (desired pressure is 1 kg/cm2)
Explain the steps taken to operate a tank-blanketing valve?
What is the process of including heat exchangers in ammonia refrigeration system?
What type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited npsha (net positive suction head available)?
What are the specialized grinding methods?
What is the maximum recommended velocity for steam in a plant pipe network?
What are the specialized crushing methods?
Name some guidelines for designing for liquid and gas velocities in process plant piping?
