Interested to Buy Any Domain ? << Click Here >> for more details...
without color coding, without nameplate, without multimeter
how can you find the type of thermocouple???
- 1 Answers
- 6260 Views
- Sabic, I also Faced
- E-Mail Answers
Answer Posted / carl_ellis
Let's assume base metal elements only, since noble metal
elements are so expensive that they are under lock and key;
adequate protection from loss of identification.
For types T, J and K, (and by exclusion, E) the options are
-a spectropscopic assay which will positively reveal the
alloys' composition, but given that the cost of an assay is
proabably 20x times the value of a base metal element, it's
not likely to happen.
- visual identification of a type T by the copper color of
its positive leg which is copper. The alloy leg is a shiny
'metallic' color.
- testing Types J or K with a magnet.
The Type J positive leg is made of iron which has a very
strong magnetic attraction.
The Type K negative leg is made of a nickel alloy which is
mildly magnetic.
Type E is non magnetic, but so are other types.
It can be tricky to distinguish mild attraction on thin
gauge wire.
Testing with a multimeter can be very misleading, because of
the difficulty in determining both the hot junction AND the
cold junction temperatures. Without accurate temperature
values, of what use is a mV reading?
Carl Ellis
Measure First
| Is This Answer Correct ? | 5 Yes | 0 No |
Post New Answer View All Answers
how many type conductivity sensor ?
where proximity sensor installed on tank in loading arm application
Draw bode plot of any transfer function. Why is plotting bode necessary?
Questions on flow meters,few questions on HART protocol,
we have level transmitter for h2s04 storage tank capacity 10k ,always there are failure of transmitter due to failure of magnetic floats ,please come up with solutions at the earliest.
What is standard procedure of manual mapping in Radar type level transmitter?
What is difference between ESD and PLC please Explain me clearly.
how do we commission inergen system?
describe flow nozzel principle?
(1) In turbine, what does term CDP, NI, NH, HSSOC, means. (2) What is the purpose of LO overhead tank in turbines.(3) An equipment is certified for EEX, IA, IIC,T6, what do you under stand by this.(4) what is SURGE, and how it is prevented, what is the purpose of bypass valve across AS valve.(5) Give 2 application of quartz crystal used for process parameter measurement.(6) what is meant by cold float of compressor shaft. (7) state four different types of flow measurement. For gas flow measurement mmscfd is the common unit. Expand the unit and specify significance of word S in the unit.(8) what is meant by Gap voltage, in vibration measurement. Normally how much Gap voltage is set and state the reason.(9) what will the new flow factor if D/P transmitter is Re-Ranged from 25” wc to 50” wc.(10) what is the usage of QDV & Volume booster.
Draw a complete P&ID of a flow suction tank indicating all control & protection equipment. Indicate all its inlets and outlets. Explain the controls for this system
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
What is megering????
Do you have reference list?
how to turbine speed measurement?
