Interested to Buy Any Domain ? << Click Here >> for more details...
Answer Posted / musa
interrupt is a process when the an external device can use
the micro-processor. it is an asynchronous signal and it is
considered as an emergency signal.Whenever the
microprocessor receives an interrupt signal, it stops
executing its current program and jumps into the interrupt
service routine(ISR). there can be more than one "source"
for the interrupt signal and each source has its own IS
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
Explain why do you use two ground pins in microprocessor 8086?
Why memory width is not 16-bit? In stead of having 8-bit (same as 8085)?
Explain what is sim and rim instructions?
List various types of interrupts available in 8051 microcontroller?
What is the bus arbitration problem in the 8086 and how can it be resolved?
How can interrupts be classified in the 8086?
Can an rc circuit be used as clock source for 8085?
explain the different types of control flags for the 8086?
What are flag registers?
What does 8088 microprocessor have?
What is 'daisy-chaining' in reference to the 8086?
With 12 mhz clock frequency how many instructions (of 1 machine cycle and 2 machine cycle) it can execute per second?
Define psp?
I have code and test bench however it is not working porperly. Need help to get it working. module fsm(clock,reset,coin,vend,state,change); \\these are the inputs and the outputs. input clock; input reset; input [2:0]coin; output vend; output [2:0]state; output [2:0]change; \\i need to define the registers as change,coin and vend reg vend; reg [2:0]change; wire [2:0]coin; \\my coins are declared as parameters to make reading better. parameter [2:0]NICKEL=3’b001; parameter [2:0]DIME=3’b010; parameter [2:0]NICKEL_DIME=3’b011; parameter [2:0]DIME_DIME=3’b100; parameter [2:0]QUARTER=3’b101; \\MY STATES ARE ALSO PARAMETERS . I DONT WANT TO MAKE YOU READ \\IN MACHINE LANGUAGE parameter [2:0]IDLE=3’b000; parameter [2:0]FIVE=3’b001; parameter [2:0]TEN=3’b010; parameter [2:0]FIFTEEN=3’b011; parameter [2:0]TWENTY=3’b100; parameter [2:0]TWENTYFIVE=3’b101; \\AS ALWAYS THE STATES ARE DEFINED AS REG reg [2:0]state,next_state; \\MY MACHINE WORKS ON STATE AND COIN always @(state or coin) begin next_state=0; \\VERYFIRST NEXT STATE IS GIVEN ZERO case(state) IDLE: case(coin) \\THIS IS THE IDLE STATE NICKEL: next_state=FIVE; DIME: next_state=TEN; QUARTER: next_state=TWENTYFIVE; default: next_state=IDLE; endcase FIVE: case(coin) \\THIS IS THE SECOND STATE NICKEL: next_state=TEN; DIME: next_state=FIFTEEN; QUARTER: next_state=TWENTYFIVE; //change=NICKEL default: next_state=FIVE; endcase TEN: case(coin) \\THIS IS THE THIRD STATE NICKEL: next_state=FIFTEEN; DIME: next_state=TWENTY; QUARTER: next_state=TWENTYFIVE; //change=DIME default: next_state=TEN; endcase FIFTEEN: case(coin) \\THIS IS THE FOURTH STATE NICKEL: next_state=TWENTY; DIME: next_state=TWENTYFIVE; QUARTER: next_state=TWENTYFIVE; //change==NICKEL_DIME default: next_state=FIFTEEN; endcase TWENTY: case(coin) \\THIS IS THE FIFTH STATE NICKEL: next_state=TWENTYFIVE; DIME: next_state=TWENTYFIVE; //change=NICKEL QUARTER: next_state=TWENTYFIVE; //change==DIME_DIME default: next_state=TWENTY; endcase TWENTYFIVE: next_state=IDLE; \\THE NEXT STATE HERE IS THE RESET default : next_state=IDLE; endcase end always @(clock) begin \\WHENEVER I GIVE A RESET I HAVE TO MAKE THE STATE TO IDLE AND VEND TO 1 if(reset) begin state <= IDLE; vend <= 1’b0; // change <= 3’b000; end \\THE CHANGE ALSO HAS TO BECOME NONE else state <= next_state; case (state) \\HERE WE DECIDE THE NEXT STATE \\ALL THE STATES ARE DEFINED HERE AND THE OUTPUT IS ALSO GIVEN IDLE: begin vend <= 1’b0; change <=3’d0; end FIVE: begin vend <= 1’b0; if (coin==QUARTER) change <=NICKEL; else change <=3’d0; TEN: begin vend <= 1’b0; if (coin==QUARTER) change <=DIME; else change <= 3’d0; FIFTEEN : begin vend <= 1’b0; if (coin==QUARTER) change <=NICKEL_DIME; else change TWENTY : begin vend <= 1’b0; if (coin==DIME) change <=NICKEL; else if (coin==QUARTER) TWENTYFIVE : begin vend <= 1’b1; change <=3’d0; end default: state <= IDLE; endcase end endmodule module test; \\THE INPUT IN THE FSM MODULE ARE REG HERE reg clock,reset; reg [2:0]coin; \\THE OUTPUT IN THE FSM MODULE ARE WIRES HERE wire vend; wire [2:0]state; wire [2:0]change; \\THE PARAMETERS AGAIN FOR THE COIN AND STATE parameter [2:0]IDLE=3’b000; parameter [2:0]FIVE=3’b001; parameter [2:0]TEN=3’b010; parameter [2:0]FIFTEEN=3’b011; parameter [2:0]TWENTY=3’b100; parameter [2:0]TWENTYFIVE=3’b101; parameter [2:0]NICKEL=3’b001; parameter [2:0]DIME=3’b010; parameter [2:0]NICKEL_DIME=3’b011; parameter [2:0]DIME_DIME=3’b100; parameter [2:0]QUARTER=3’b101; \\I MONITOR THE TIME,DRINK,RESET,CLOCK,STATE AND CHANGE FOR CHANGES. initial begin $display("Time\tcoin\tdrink\treset\tclock\tstate\tchange"); $monitor("%g\t%b\t%b\t%b\t%b\t%d\t% d",$time,coin,vend,reset,clock,state,change); \\NEW FEATURE: MY MACHINE HAS THE FACILITY TO DUMP VARIABLES SO THAT \\ I CAN VIEW THEM USING A VCD VIEWER. $dumpvars; $dumpfile("file.vcd"); // Dump output file. \\THIS IS WHERE THE COINS ARE ADDED. clock=0; reset=1; \\FIRST LETS RESET THE MACHINE #2 reset=0; coin=NICKEL; \\CHECK FOR STATE 1 #2 reset=1; coin=2’b00; #2 reset=0; coin=DIME; \\RESET AGAIN AND CHECK FOR STATE 2 #2 reset=1; coin=2’b00; #2 reset=0; \\RESET AGAIN AND CHECK FOR STATE 5 coin=QUARTER; #2 reset=1; coin=2’b00; #2 reset=0; \\RESET AGAIN AND CHECK FOR STATE 5 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 reset=1; coin=2’b00; #2 reset=0; \\RESET AGAIN AND CHECK FOR STATE 5 AND SO ON coin=NICKEL; #2 coin=DIME; #2 coin=DIME; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=DIME; #2 coin=QUARTER; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=DIME; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=DIME; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=NICKEL; #2 coin=QUARTER; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=QUARTER; #2 reset=1; coin=2’b00; #2 $finish; end \\THE CLOCK NEEDS TO TICK EVERY 2 TIME UNIT always #1 clock=~clock; //always @(state) // coin=!coin; initial begin if (reset) coin=2’b00; end \\THIS IS WHERE I INSTANTIATE THE MACHINE fsm inst1(clock,reset,coin,vend,state,change); endmodule
Explain dma?
