Interested to Buy Any Domain ? << Click Here >> for more details...
Answer Posted / kj
The auto reclosure relay is often used in a distribution
system. If a breaker opens on a fault the fault may be
cleared by the fault current of the fault may clear it
self. An example of this is where something hits the power
lines during a storm. It may cause a short circuit open the
breaker. The could be a tree limb shorting across the lines
or pushing the lines together and then falling clear.
In circumstances like this the breaker would normally stay
open until someone access it and reclosed it.
What the reclose relay does is that after a set time delay
it will send a close signal to the breaker. This will then
restore the supply. If all is well the electricity company
can check for the problem later.
If there is still a fault the breaker will open and the
reclose relay will close one more time. If the fault still
exists the reclose relay will lock out until reset.
| Is This Answer Correct ? | 6 Yes | 0 No |
Post New Answer View All Answers
why we r not earthed Control cable of C.T. terminals
power transmission pole used one support , that only for support or earthing
any one can explain what is the size of pvc,armoured, various sizes of powr cable dia?
I don't understand why when we connect high voltage source in DC to electronic motor , we must add capacitor and resistor in parallel ? (I know that we use capacitor because we want to absorb the current that in the first second electronic motor in opposed with current course produce. ) what are the feature of Resistor and in such situation ?
in non technical way how can u define POWER FACTOR??
what is the meaning of osr in transformer.
what is the need of starter in tube light and what type of starter is used in that?
We have studied about many techniques for finding the stability of system, ROOT LOCUS, ROUTH, BODE PLOT, POLER PLOT etc. In these which is used where. what are the difference among them... PLZ tell me.......
What is the difference between a 3 winding and 2 winding Potential Transformer
What is the Good Earth resistance value of G.I & Cu. Chemical Earthing & Normal Pipe Earthing?
What is the most essential condition for the voltage build up for a d.c. Shunt generator?
How can claculate to attain the desired PF in the line ( HOW Much KVAR is required ) Pls Give the formula? Equate Petrochemical 0 1 how to calculate sizing of NGTR (Transformer rating,Loading resistor value and Current rating of resistor) and what is the X/R ratio. Details : 11kV,Capacitance 1.73532 micro farads,40kA for 1sec. 0 1 What will happened. if we feed 3phase supplay to the stater with out insert the rotor. How much current will flow through the stater winnding? Equate Petrochemical 0 1 What is required of exietation to the alternater. 0 1 why star point of HT motor not earthed? Equate Petrochemical 0 1 Why we are getting low voltage in star connection? Equate Petrochemical 0 2 What's ND relay & it's functions? Equate Petrochemical 0 2 How instantanious short circuit current is calculated? its formula? Equate Petrochemical 0 2 What is servo Motor? What's the advantages of this motor over Induction motor? Equate Petrochemical 0 2 What is core CT & it's function? Equate Petrochemical 0 3 what is meant by star/delta voltages as 440/220 in a 3 phase induction motor, and why it should be connected on STAR IN 3 PHASE SUPPLY L & T 0 4 What is required of exietation to the alternater. KNB 1 23 what is the design voltage for 6.6KV 2000 KVAR HT capacitor? Consultancy 0 3 Pls explain about vfd control?Where it is used, Give some example? siemens 1 22 Please explain me abt PQ diagaram in the power sector. 0 9
What is the RME and explain the full form and what is the RME work?
What is the formulae of Megger value for a A.C.Motor
what is the thumb rule for determination resistance of resistor?
