Interested to Buy Any Domain ? << Click Here >> for more details...
why we are using perforted cable tray for control cable and
ladder tray for power cable
- 1 Answers
- 9192 Views
- I also Faced
- E-Mail Answers
Answer Posted / rezvanian
Due to the high current flowing through the power cable
that warms the cable and its temperature rises so we use
ladder tray for power cable and the temperature of the
power cable can be exchanged with the surroundings.
We cant use ladder tray for control cables because the
control cables have high bending capability ( flexibility)
which is dropping belly ( belly bend downward ) and the
control cables temperature is always near the ambient
temperature and the perforated cable tray is suitable.
| Is This Answer Correct ? | 14 Yes | 3 No |
Post New Answer View All Answers
1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling
i have steam drum height 1000mm. and i want to placed the transmitter below the tap.how i calculate.
What are de-saturators?
A length of steel pipe is used to carry sea water to a desalination plant. An adequate corrosion allowance must be specified and indicated in the piping specification, which affects the _________________________ of the pipe
-/5A. What is the meaning and limitations of this in energy meter constant. It is a 3 phase LT Energy Meter. If this Energy Meter is connected through a CT of ratio 200/5 Amps, then what is the multiplying constant and how its will be calculated.
How an rtd work, and what volts/current goes to a rtd to measure the resistance?
We Have Two Field bus Pressure Transmitters of Different Sensor Range (I.E One is of Lower range and Another is of Higher Range).Is same Process Line. My Question is Can i provide Saturation Limit to my field Bus Transmitter as We can provide Saturation current limit to HART Instruments. As During Low Pressure Both Working OK ,But During High Pressure, transmitter with Lower sensor range Goes to Fault mode as Beyond its Sensor Limit it can Measure, So may I provide Saturation point Some where to Suppress This Fault during High Pressure.
tell me the field & lab calibration procedure step by step with diagram of pressure gauge, pressure switch, pressure transmitter, temperature switch, level switch, flow switch, flow transmitter, temperature transmitter, temperature indicator, flow indicator, level indicator, control valve, thermocouple, pressure indicator (digital & analogue),
How hart protocol can be connected with control valves?
in valve is constructed as per SME B 16.34, then which standard is used for fire testing of valve?.
How digital input and digital output 's are working in dcs
while am calibrating Drager polytron 2IR flame gas detector occured non zero status.how can i get zero status?
please tel me the calibration of pneumatic controler.
principle of dead weight tester ?
Explain about the leakage class of the control valves
