Interested to Buy Any Domain ? << Click Here >> for more details...
why the back wheel in the tractor is bigger than the front
wheel?
- 23 Answers
- 49922 Views
- L&T, MAHINDRA, RAS, I also Faced
- E-Mail Answers
Answer Posted / zakir hussain
rear wheel in tractor is bigger to have more
torque /traction because bigger the dia more is the torque
| Is This Answer Correct ? | 0 Yes | 1 No |
Post New Answer View All Answers
How much should be the minimum and maximum suction and discharge pressure of screw chiller plant.
What causes cylinder liner-wear down?
What is the sensitive part of the liner
sir iam vinod kumar i have done B.TECH. in mechanical engg in 2007 i want to choose career as section engg.please give the information about coaching institute.
1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?
What pressure is highest L.O. Gravity Head or S.W. of the stern tube circulation
why the path of a satellite is always elliptical with earth not at the centre of the ellipse?
Name Of Parts And Each Purpose
should cutouts made in main header of metal ducting be deducted from duct measurement.
how does a generator work?
written test: 1) periodical and monthly maintenance are called preventive or panned maintenance. 2) Mechanical seal parts and their material. 3)Urea plant main parts and their construction material details.4)Name diagram of the given turbine5) Turbine nomenclature like API name.6)All types of corrosion like Galvanic and oxide with example.7)Parts of gate valve and its usage. diaphragm gate valve usage. etc.....
why we cant measure absolute entropy directly,but the change we can?
What is a time and motion theory?
asked about the power transimmisions and types of power drives and about milling different process types and differnce between straddle milling and gang milling
hi, if anyone have previous year paper of NHPC or some questions, Please send me at gupta.pankaj20@gmail.com
