What is A check, B check, C Check & D check for a diesel
Generator? Please guide me as this question was asked many
times and till now i haven't get right answer.If you can mail
me then please mail me the answer @ yogiagarwal@gmail.com.
- 20 Answers
- 489498 Views
- Apollo Power, BDV, Bosch, Further Future, Honda, HVCC, Jackson, Kirloskar, Multi Arc, Ranbaxy, Regulus IMC, TVS, XCD, YWS, I also Faced
- E-Mail Answers
Answer Posted / amit kumar rathi
A-Check (Daily routein Check)
1. Check oil level.
2. Check cleanliness of DG
3. Check Battery Voltage
4. Check any Leakage
5. Check all filter condition
6. Check oil Level
7. Check coolent Level
8. Check Check V-Belt condition
B-Check (Every 300- 350 Hrs.)
1. Change oil.
2. Change oil filter,fuel filter,bypass filter.
3. Change Air Filter.
4. Change water Separator
5. Radiator cleaning with chamical
C-Check (Every 800-1500 Hrs.)
1. Change oil.
2. Change oil filter,fuel filter,bypass filter.
3. Change Air Filter.
4. Change water Separator
5. Radiator cleaning with chamical
6. Check All Electrical terminal & thimbles
7. Check polution level
D-check (Every 3000- 5000 Hrs.)
1. Complete DG set should be dismental.
2. Turbo charger service
3. Injector Pin service
4. Cylinder Head service
5. PT Pump sevice &
6. Repeat same B-Check process.
If your DG set running hours more than 10,000 then in D-
Check You should need to be
1. Change Piston Bearing,
2. Change nozels,
3. Piston Cylinder also need to be change.
4. Change Canopy filter if require
5. Check polution level
| Is This Answer Correct ? | 1543 Yes | 97 No |
Post New Answer View All Answers
What is the most basic characteristic of supercritical boilers?
thermal engg
How to disiegn DCV circuit ?
how many types of suspensions are used in automobiles?
What are the benefits of cycloidal gears?
What are the causes of positive and negative propeller slip?
What is diffrence between star & delta connnection in practical situation in submersible pump?
why boiler is closed system ?
What is "H7014C/HQ1P4 BEARING" means ???
Why pert is preferred over cpm for evaluation of project ?
2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand
present salary with all benefits (ctc) please give breakup it possible ?
interviw tips for bhel supervisor trainee
I want technical questions of previous reqruitment examination
I want to model a piezoelectric beam in ansys software.How can I model the electrical circuit and how can I read the general current and voltage produced by the PZ?
