why free wheeling diode is connected across inductive load
- 16 Answers
- 54035 Views
- NTPC, Omaxe, Wipro, I also Faced
- E-Mail Answers
Answer Posted / rajneesh
Free wheeling diodes are used whenever inductive loads are
switched off by silicon components: in relay drivers,
H-bridge motor drivers, and so on. A switched-mode power
supply also exploits this effect, but the energy is not
dissipated to heat but used for pumping additional charge
through the load.
this is the reason......
| Is This Answer Correct ? | 1 Yes | 1 No |
Post New Answer View All Answers
When we use air circuit breaker, it has O/L protection ,time delay SC protection, Instataneous SC protection & ground fault protection. They all have some setting range. But what is the suitable/allowable setting for the above protection which will be safe for the equipment? For example-O/L protection setting have a range of (0.4,0.45,0.5,0.55,0.6,0.65,0.7,0.8,0.9,1.0)xIn Time delay SC protection have a range of (1.25,1.5,2,3,4,6,8,10,12)xIn Time delay setting is 0.02,0.1,0.2,0.3,0.4 Instataneous setting is fixed to 20xIn Gound fault setting is given 100A,300A,600A,900A,1200A This setting are for 2500A ACB. So what will be the basic allowable setting for the above protection? is there any formulae to calculate this<
How to know Resistance and Reactance value of main and aux winding of single phase capacitor start capacitor run induction motor to find capacitor value?
Whats the minimum value for I.R. that can be allowed for HT & LT alternators for operation?
I am going to appear for the RRB Chennai junior Engineer online exam. Please send me the previous exams question papers (also solved) to my mail id: rrkhandhar@yahoo.com
what is th basic difference between a d latch time line and a d flip flop time line???
Factory acceptance test. FAT. For 132 kv transmisstion towers what is that meaning and what are the tests commonly companies perform now days.
how we calculate electrical load on a building according to area?
how do we calculate length of starting time and repeated starting of a direct online starter?
what is the effect of higher value of GD???
what are the possible reaons & remedies if resistance of NGR getting heat up
The power supplied to a 33microF capacitor from a 120V, 60Hz source will be
one split ac how can told of this ac which Tr tell me us
1. A 380 / 220 V r.m.s. 3-phase 4-wire circuit carries loads of 8 + j8.1 ohm; 4 + j4.1 ohm; and 2 +j2.1 ohmin the three phases respectively. The length of the circuit is 100 m, and the resistivity of the phase conductors is 0.0005 Ω/m. The neutral conductor is of the same size as the phase conductors. a) Select a reference angle 0for the first phase. Then write down the three phase voltages in both polar format and complex number format. b) Make appropriate assumptions, and take temperature effects on resistance is insignificant. Calculate the currents in the three phases. (Note: Determine conductor resistance, and apply Kirchhoff’s Voltage Law) Based on the result, suggest a main switch rating for the circuit. c) Show your preferred direction of neutral current in a diagram, and then determine its value. (Note: Apply superposition principle, and Kirchhoff’s Current Law) Use its magnitude to show that in this circuit, the unbalanced load may increase the voltage drop in some of the phases. (Note: Also observe the common volt drip in neutral) State your assumptions, if there are any. d) Suddenly the neutral wire of the circuit is broken. Estimate the new currents in the first phase, i.e. Phase L1. State your assumptions, if there are any.
do we use links in a dc circuit?if so what s its use in it?
mccb service sittings be done?
