Interested to Buy Any Domain ? << Click Here >> for more details...
what is the per unit cost of generation of electricity at thermal,hydro,desael,solar,gas power plant
- 1 Answers
- 4479 Views
- I also Faced
- E-Mail Answers
Answer Posted / k.prakashchandra
Several factors decide the cost.e.g. SGS in Karnataka is
supplying at 13p per unit whereas mini hydels charge about
Rs 3 per unit.However the cost in Rs may roughly taken as 1,
hydel -2,2. Thermal-3,3. diesel-8,4.Solar-4 5. gas -3, 5.
wind-3.5
| Is This Answer Correct ? | 1 Yes | 4 No |
Post New Answer View All Answers
what is the voltage between earth to neutral in lift.
A generating system will have a total capacity of 300 MW. Find the probable forced outage when the capacity is supplied by two 150 MW units. The operating probability of all units is P=0.98 and forced outage probability rate Q =0.02 .
how does a submersible pump work..?
Why do you have to use Protecion relay with the function MTB ( Mechanical Trip Button ) for electrical system.
WHat is the requirement of installing FAST ACTING EARTH SWITCH in GIS and how is that integrated with protection system. How and when does it operate?
I want to put this query to SENIOR & EXPERIENCED ELECTRICAL ENGINEERS. 1)I want to know about the control circuit diagrams for control panels. I found it difficult to understand. Is there ant booklet through which we can learn the circuit diagrams? 2)I want to learn about conduiting, laying cables, preparing cable schedules and various techniques which is the part of building infrastucture(construction field). I don't have any experience in this area. I have experience in control panels only. that's why i am not getting any opening in building infrastucture (construction field).Can I get the job in this field as Trainee Engineer? How to enter this field? I need job in PUNE
what kn of disc is used in 33kv,132kv,220kv,400kv,800kv transmission line
at work i have a genertor/alternater what is the easyest way to work out if it is dc or ac?
How phase to phase voltage comes 440V.
Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1. H1-H2 = H2-H3 H3-H1 2. H2-H3 = H3-H1 H1-H2 3. H3-H1 = H1-H2 H2-H3 For the LV side also: 4. X1-X0 = X2-X0 X3-X0 5. X2-X0 = X3-X0 X1-X0 6. X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0 H2-H0 H3-H0 X0-X1 X0-X2 X0-X3 128.0 119.9 7.2 29.2 13.3 15.8 70.7 128.4 59.2 23.4 22.0 3.6 7.2 120.1 128.1 13.4 29.3 15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone?
Why efficiency of generator is higher than motor at a particular load?
what kelvin's law ?
How maesure earth neutral value & how much maximum value value required in between earth & neutral.
CAN ANYBODY PLEASE TELL ME HOW TO DESIGN A SERIES REACTOR FOR LIMITING SHORT CIRCUIT FAULT CURRENT??
Can anybody inform me about the pattern of ECIL GET( Graduate Engineers Trainee) interview for Electrical students? Will there be HR round as well? I thought of preparing for 2 to 3 subjects thoroughly. Will it be sufficient? Please share your thoughts.
