Interested to Buy Any Domain ? << Click Here >> for more details...
difference between dol and rdol startors?
- 2 Answers
- 33875 Views
- Vijai Electricals, I also Faced
- E-Mail Answers
Answer Posted / madhu
RDOL IS NOTHING BUT REVERSIBLE DIRECT ON LINE STARTER.
This kind of starter is required when the motor is required
to run in both forward as well as reverse directions
according to the application.
Power circuit: There is one more power contactor connected
across the power contactor in the power circuit with two of
the phases interchanged to achieve reversal of rotation. The
two contactors are mechanically interlocked to ensure that
both of them do not operate simultaneously. The shorting of
two different phases is avoided through this arrangement.
Control circuit: The control circuit obviously consists of
two start push buttons, one for ‘FORWARD START’ and another
for ‘REVERSE START’. Each of them controls the supply to the
respective contactor coils responsible for the supply to the
motor in forward and reverse modes. The stop command is
common for both modes since it is independent of type of
operation. The NC contact of forward contactor is connected
in series with reverse contactor coil and that of reverse
contactor is connected in series with forward contactor
coil. This is the electrical interlock, which ensures that
only one contactor will pick up at a time avoiding any
mal-operation and consequent damage to the feeder and
problems to the dependant processes.
•
Indication circuit: One more Red LED is required to indicate
the ‘Reverse ON’ mode.
One NO contact of the reverse contactor is connected in
series with it.
| Is This Answer Correct ? | 26 Yes | 6 No |
Post New Answer View All Answers
can some one clearly explain why -48 volt DC use in telecom site????
In Dyn11 power transformer if any one of the 3 phases connected to earth in star connected side then please explain effect of the current flow in delta connected side of transformer.(In this case if one phase is shorted to ground in star connected side then we observe the current flow in two phases only not three phases in delta connected primary side. Please explain why it is so?)
what is the meaning of the symbol << >> put in transformer drawing
dg started in plc mode and load taken later one battery terminal connection will be disconnected by loose connection what will happen for dg and shall we connect battery terminals while dg in load time?
i have a 4 Mva transformer 34.5 kv / 480-277 v and i used 2 parallel 3200 amp bus duct for the secondary feeder using 3 ply of bus bar ( 3/8" x 5" ) as a common where the flexible link terminated and 6300 amps breaker for the main, the lower bus duct reaches 70 degrees and the upper bus duct reaches 55 degrees when i used thermal scanner. why the temperature is not balance when the load reaches 3600 amps.
If a current -8+6sin6t is flowing three ammeter, one is a centre zero PMMC meter, one is true rms meter and one is moving iron meter. What are the reading of these three meter respectively?
WHAT IS THE TECHNICAL SPECIFICATION OF C CURVE & D CURVE LEGRAND MAKE MCB
role of europe union in UK safety legistlation (electrical safety)
How to derive detailed design of Suitable bus Bar for 100A for 6.6KV?
If more than rated DC voltage appears across trip coil of the breaker, what will happen? e.g. in 110V DC circuit system, if voltage across battery terminal showing 121 V
how is find out kwh step by step
if the load is 80 amp for main fuse and 100 amp for breaker so how can we calculate the cable size (cooper ) .
i have total 8 dg sets for synchronizing and 2 buscoupler,1 sectoin dg no 1,2,3,and 2 sectoin dg no 4,5,6,and last section dg no 7,8 ....if buscupler no 1 and 2 is off mode ..than dg no 1,2,3,will synchroniz of another dg sets?
Do you need any help with FEWA Electrical Supervisor exams?
please suggest some good universities with low cost iam in totally full confusion so please help me my profile gre 283 and ielts 5.5
