What is difference between Dy11 & Dyn11 vector group
transformer. Can both these transformers operate in
parrallel.
- 5 Answers
- 60811 Views
- Jaypee, JOY, I also Faced
- E-Mail Answers
Answer Posted / ravi
Winding connection designations
High Voltage Always capital letters
Delta - D
Star - S
Interconnected star - Z
Neutral brought out - N
Low voltage Always small letters
Delta - d
Star - s
Interconnected star - z
Neutral brought out - n
Phase displacement
Phase rotation is always anti-clockwise. (international
adopted convention)
Use the hour indicator as the indicating phase displacement
angle. Because there are 12 hours on a clock, and a circle
consists out of 360°, each hour represents 30°.
Thus 1 = 30°, 2 = 60°, 3 = 90°, 6 = 180° and 12 = 0° or
360°.
The minute hand is set on 12 o'clock and replaces the line
to neutral voltage (sometimes imaginary) of the HV winding.
This position is always the reference point.
Because rotation is anti-clockwise, 1 = 30° lagging (LV
lags HV with 30°)and 11 = 330° lagging or 30° leading (LV
leads HV with 30°)
To summarise:
Dd0
Delta connected HV winding, delta connected LV winding, no
phase shift between HV and LV.
Dyn11
Delta connected HV winding, star connected LV winding with
neutral brought out, LV is leading HV with 30°
YNd5
Star connected HV winding with neutral brought out, delta
connected LV winding, LV lags HV with 150°
" So there is no specification of Dy11.. it will be Dyn11 "
| Is This Answer Correct ? | 63 Yes | 18 No |
Post New Answer View All Answers
what is the difference between general inverter and solor inverter clerly explain plz
In the ACB breaker capacity is 2000Amp but this each phase taken 1250 But total beldibg load is 600amp or 700amp watt is the problem
we have 15 ampere variyac but we want 30 ampere variyac what we do
i want bhel placement paper for electrical if anybody having pl send to my id kavitha867@myway.com immediately
1)How much current can a 3-1/2 core 100 mm wire carry? 2)What are the special cables required for explosion proof wiring? 3)In case you do not have coal and salt for earthing, how can you achieve good temporary earthing? 4)One horse power single phase motor is more likely to get hot than a one horse power 3 phase motor. Is it true or false, if true why? 5)What are the different types of soft starters for large motors?please explain?
I have 1500/1A CT If i connect this CT in 6.6KV bus bar means what will be the voltage present in CT?
how much GROUND & NEUTRAL VOLT maintain in data center.
What are the advantage of free wheeling diode in a full wave rectifier?
What type of wiring series or parallel is used for conventional and addressable type FAS & why?
what's the difference between 'shaft power demand' and 'BHP' , when we consider electrical load list.
How Can You Relate Power Engineering With Electrical Engineering?
WE know that for Inductor X=2pifL,In DC f=0,then X=0 so,V=IX=0;But In the DC excitation of rotor of AC generator,DC motor field coil which coils are inductor so why does not applying DC voltage short the rotor coil of AC generator and field coil of motor?If it would then DC source might be damaged but it is not happened. Why does the strand conductor of Electrical power transmission line make twist?
What facility we get after CT secondary earthing and how?
what will happen if i connect 12 volt battery with 24 volt battery charger.
How does "OUT OF STEP" relay ,for Synchronous motor protection, work?
