Interested to Buy Any Domain ? << Click Here >> for more details...
What is the difference between short circuit and overload
currents?
- 14 Answers
- 62612 Views
- IIIT, I also Faced
- E-Mail Answers
Answer Posted / crosswind
I agree with answer #8 short circuit have diffrent types of
fauls L-L, L-G, 3ph S/Cetc seee iec-60909.the S/C current
when to hot wires (un-grounded) wire make unintended
contact with each other; p 2 p S/c has thus been created.It
created unbalance fault of the system.This means
interruption of the system.... unlike Overload current is
interrrupted the load itself by means of overload
protection setting (Thermal Load) relay operated well to
trip. This mostly different not the same ..In shotr S/c
interrrup the system Max. interrrupting value (Ka) while
Overload currents happens only in motors stated by answer#8
Additinally,S/C analysis is onthe importance in power
system study because it protec the whole system by the
right choices of prtection device and by the right study of
devise -coordination the tripping curve will not overlap
with respect to the point of S/C fault who will be the
first to tripp rather than the last breker it was so called
the selection of the right tripping ( Long & Short Circuit
delay)
| Is This Answer Correct ? | 4 Yes | 14 No |
Post New Answer View All Answers
Sir,In our company there are 3 caterpillar make(capacity:(1) 3.3KV,2.5MW(2)3.3KV,2.5MW & (3)3.3KV,1.9MW) & 1 deutz make (capacity:11KV,3.8MW)gas engines utilised,all are running in paralell. There are three transformer utilised,(1) 6.25MVA,3.3KV/22KV,Impedence voltage:6.7% used for two generator,both are 2.5MW(2)5.5MVA,3.3KV/22KV,Impedence voltage:7.2% used for one generator of 2.5MW & (3) 5.5MVA,11KV/22KV,Impedence voltage:7.8% used for one generator of 2.5MW.all generator breakers capacity of 1250Amps. Sir,I want the details of fault level calculation of generator,transformer individually & for whole system. If you require any information from me.feel free for contact me sir.pl.send the answer of my question as the earliest as possible.
How to calculate cable rating for 3 phase supply?
how can i apilly for electrical c licencese.sir,i completed B.Tech in electrical & electronics engineering in 201onot working any company
why do motors burn out? I understand why adding parallel loads to a power source means more current moves through the circuit, and can destroy circuit elements by overheating. What about when you have a vaccuum cleaner intake flush against a floor, a room fan sitting directly against a wall, or a power drill trying to drill through something too hard?
Define open loop control system.
Is there any type of starter for DC motor other than two point,Three point and Four point starters?
12.5 tons a/c is their how much kva generator can recommend to the customer.
any body,pls tell me how to done relay coordination ? how to coordinate by TCC curve?how to read the tcc curve?
I have experienced electrical maintenance HT ,but I completed be ECE ....can I apply c license or not ???? Pls help me friend s...
Define coil span?
How many types of instrument cables are there?
sir please send me iocl written test paper in my e-mail account. i'll be obliged to you........ thank u roshan
WRITEDOWN FEW RELY CODES
What is a surge supressor why its is used in synchronous generators
WHAT R THE SAFETIES IN A HIGH TENSION PANEL N LOW TENSION PANEL. ALSO WAT SAFETIES R THERE IN A 200 KVA TRANSFORMER?
