Interested to Buy Any Domain ? << Click Here >> for more details...
take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
- 6 Answers
- 7982 Views
- AT&T, I also Faced
- E-Mail Answers
Answer Posted / shahin
Configuration -
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
Ra(config)#access-class 2 in
From the above configuration one thing is clear that only
host from 10.1.1.0 network (i.e Switch 2)can access the telnet.
Host from 10.1.2.0 network are not allowed to access the
TELNET. As the access list specified on vitual terminal ie.
line vty 0 4.
So [B] is the correct answer.
[B] To prevent sw1 host from accessing command prompt
I configure ur scenario in PACKET TRACER & configure
accordingly.
After that i tried to access TELNET from client of Switch2,
i wz successful. Ie. Router allow to access the TELNET.
After that i tried to access TELNET from client of Switch1,
i wzn't successful.Ie Router doesn't allow to access the TELNET.
On the option, it create little bit confusion on mind..
COMMAND PROMPT of which device... off course its ROUTER.
If the option were written in specific, than i think no
confusion will arise.
I hope, it will help u..!!
Let me know my feedback..!!
thanxx for such a gud question.
| Is This Answer Correct ? | 0 Yes | 0 No |
Post New Answer View All Answers
Explain the term 'multicast'.
Briefly explain the conversion steps in data encapsulation.
What is the size of IP address?
What is the simplest way to remotely configure a router?
How do we do encryption and authentication in L2F?
how we update the IOS version with the help of TFTP?
If there is only 2 host in bus topology is that possible collision accord?
What are the differnt memory use in cisco router?
What is the terminal emulation, in which layer it comes?
Explain why is udp lease favored when compared to tcp?
Can you explain encapsulating, carrier and passenger protocol?
What are the different memories used in a CISCO router?
What are the advantages of lan switching?
After how long keep alive messages exchange in eigrp?
what is the concept of HA and FA in VPN tunneling?
