Interested to Buy Any Domain ? << Click Here >> for more details...
AIR CONDITIONERS HAVE RATING IN BTU AND TON OR SOMETIMES
IN KW ALSO... WHAT IS THEIR RELATION?
ALSO ACs HAVE TWO POWERS (IN WATTS) WRITTEN ON THEIR NAME
PLATES WHAT DOES EACH MEAN?
HOW TO DETERMINE THE RUNNING CURRENT IN AMPERES OR THE
ENERGY CONSUMED IN WATTS?
WHAT IS THE THUMB RULE FOR DETERMINING THE CURRENT AND TON
OF AN AC?
- 7 Answers
- 20866 Views
- Carrier, HAL, I also Faced
- E-Mail Answers
Answer Posted / prakash suhane
Relation mentioned in answer 1,2 and 3 are correct.
Some compressor mention two powers one is Electrical power
in wattage and other is Mechanicle power in T.R or B.T.U
To determine the Energy Consumed use falowing formula.
For 1 phase K.W = Voltage * Ampere * power factor
use clampmeter to take running current of compressor.
T.R calculation is depend on various factors (hence there
is no thumb rule)
1) Room size
2) Worst ambient condition around room
3) No. of Doors and Windows.
4) Occupancy, No. of Light etc
once you calculate T.R then u can find K.W by using
fallowing relation 1 T.R = 3.53 K. W
and hence once u get K.W then calculate the full load
current by using above mentioned formula.
| Is This Answer Correct ? | 23 Yes | 7 No |
Post New Answer View All Answers
What is coefficient of contraction?
Draw the flow of F.O. diagram from service tank to Main Engine?
What are the typical indicator diagrams?
What is meant by running clearance?
tell me about a time you were able to successfully deal with another person even when that individual may not have personally liked you or vice versa.
We have 6-axis wotan horizontal milling & boring machine. Linear axis- x,y,z,w & U. Rotary table B Axis Z,U & W axis are parallel. Z is tool axis. X is cross slide. We wish to retrofit the machine.Which control I should select & also suggest How many axis simutaneous control for linear & circular interpolation.
1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?
Explain working of Kaplan turbine?
what is bms system and how to work it
Mention stefan boltzman contant.
Interview question paper
What is the ratio of specific heat of air?
where we can get the surfacing modelling project of example to practice in catia.
I want to know flow rate,max pressure drop,heat load,design pressure,test presurre,temp both inlet and outlet of coldside and hot side of 1,2,3,5,5.5,7.5,10,12,15 tons
What are materials used for manufacturing of gears ?
