what is meant by form factor and hoe related with the HT
transmission voltage
- 2 Answers
- 7198 Views
- I also Faced
- E-Mail Answers
Answer Posted / chandrashekar g
form factor is the ratio of r.m.s value to average value of
any electrcial quantity
ff=r.m.s/ave. value
0.70vm/0.63vm=1.1 where vm=max.voltage
do u know the formula for finding emf of transformer
E=4*1.1*Øm*f*Np volts
where
1.1=form factor
Øm=Bmax*A
f=frequency
Np= no. of primary turns
so transmission depends on form factor
| Is This Answer Correct ? | 14 Yes | 2 No |
Post New Answer View All Answers
What is the best thing to protect the motor from running over full current. CT or O/L or pressure transducer at the given pressure rating
How may I enrol or get admission to your program?
what is the voltage regulation for unity and zero power factor?
Why the moulded plug comes with domestic appliances instead of assembled plug like anchor, Vinay 5/15 A.
What are the three constants associated with a steady state error?
How we calculate DC inducation moter Amp? Sir pls give me formula......
TRAFO 1. WHY BREATHER IS USED. 2. WHY OIL GOES DOWN IN CONSERVATOR TANK. 3. WHY WE ARE TAKING OIL SAMPLE TAKING FROM BOTTOM OF TRANSFORMER. 4. HOW TO CHECK IR VALUE OF TRANSFORMER. 5. WHY OLTC HAVING BUCHHOLZ TRIP ONLY; WHY NO ALARM. 6. OFF LOAD TAP CHANGER OPERATION PROCEDURE. 7. TR. SHUTDOWN / ISOLATION PROCEDURE. 8. WHEN THREE TRS. IN PARALLEL, ONE TR. IS NOT SHARING THE LOAD – WHAT IS REASON AND WHAT YOU WILL DO. 9. WHY TR. HAS OLTC IN HV SIDE. 10. WHAT IS % IMPEDANCE. 11. WHY TR. RATING IN MVA. 12. WHAT IS VECTOR GROUP IN TR. 13. CONDITION FOR PARALLEL OPERATION OF TRS. 14. WHAT IS TERTIARY WINDING. WHERE IT WILL BE. 15. IF TR. TRIP ON BUCHHOLZ OR TAP CHANGER RELAY, WHAT YOU WILL DO. 16. DIFFERENCE BETWEEN OIL TEMP. AND WINDING TEMP. PROTECTION 17. HOW WINDING TEMP. IS MEASURED IN CAST RESIN TR. 18. DIFFERENT TYPES OF FAULTS IN TR. Trafo - Page-1 of 2 19. WHAT HAPPENS WHEN TR. CHARGED FROM LV. 20. WHAT WILL YOU DO IF MEGGER READING SHOWS ZERO BETWEEN LV WINDING AND EARTH. 21. CAN WE INTERCHANGE BUCHHOLZ RELAY OF MAIN TANK AND OLTC TANK. 22. IF THE LINE BETWEEN BREATHER AND CONSERVATOR TANK 23. LOCKED, WHAT WILL HAPPEN DURING LOAD CYCLE. 24. WHAT IS THE FUNCTION OF OIL SEAL IN BREATHER. 25. WHAT ARE LOCATIONS FOR BUCHHOLZ RELAY FIXED IN POWER TR. 26. WHAT ARE CHECKS IN POWER TR. DURING MAINTENANCE. 27. WHAT IS IMPORTANT WHEN WE CHECK OLTC OPERATION DURING MAINTENANCE. Trafo - Page 2 of 2
bsec exam syllabus (mis)
we are having 15kw and 3kw motor both can run in same time , instead of using copper we are using ug aluminium cable , 35 sq.mm is suitable for its current carrying capacity..?
Why do we need interlocking in a HT metering or Ring main unit switchgear?
What is the need of earthing transformer for delta side of a transformer. (Think of a line section between a star/delta transformer at a grid substation and delta/star transformer at a village. An earthing transformer is there at the delta side of the star/delta transformer at grid substation). As there are no ground reference there will not be fault current if a one phase is grounded. Further L-L phase will be sensed by the primary side of star/delta transformer as a L-G fault. So why an earthing transformer is required at delta side
What is the formulae of Megger value for a A.C.Motor
can anyone explain the star-delta motor control wiring ,which wire go where and how they operate?
What is mean by hot and cold loop testing?
Dyn1 transformer vector group testing how to do
