I have an UI issue "please fill out this field" pop up in firefox browser keeps scrolling with the page is it valid???

i have to install a HT panel, what components, I have to use in this and what will the diagram of that diagram,please tell me each and everything.

Hi everyone i want to learn Devops in Hyderabad can anyone please suggest me best institute.

Sir please confirm job work sale for clothes shat d1 yes & no

in a table is b in column k (manikanta,sivananda,muralidhar) i want result like (mnikanta,sivnanda,murlidhar) please slove it

In an existing power plant (phase I) with step up transformers (3nos) with Ynd1 vector group to the 400KV bus bar,an extension power plant (phase II) with transformers (4nos) with Ynd11 vector group >. what are the consequences of such configuration ,please note that % impedance are also differ i.e. 15% & 10.5% the reason was that auxiliary supply interface is at different voltage levels i.e 400v & 6.6KV in phase i and phase II respectively .please advise ! Thank you !

could any help me please, how to work on visual foxpro application using UFT

NA,

how to make Enrofloxacin 20% solution & whats remedy to avoid crystal formation in this batch after 15 -20days? Please anybody assist in it

Can i please VHDL code for D-Latch with clear input ?? (HINT: Set up a “Process” with appropriate sensitivity list to get the desired D-Latch with Clr working.) Inputs and Outputs: entity Lab4b is Port ( Clr, Clk, D : in STD_LOGIC; Q : out STD_LOGIC); end Lab4b;

how can you explain your Real Estate Project in front of interviewer..? please step by step......

CHEMICAL ENERGY BALANCE - EXAMPLE 11.1 : Please match the term A - E with the stated definition i - v. Terms : A. Yield. B. Selectivity. C. Relative saturation. D. Molal saturation. E. Absolute saturation. Definitions : i. (moles of desired product formed) / (moles that would have been formed if there were no side reactions and the limiting reactant has reacted completely); ii. (moles of desired product formed) / (moles of undesired product formed); iii. (relative humidity 40 % means partial pressure of water vapour equals 4 / 10 of the vapour pressure of water at the system temperature); iv. (moles of vapour) / (moles of vapour dry gas); v. (mass of vapour) / (mass of dry gas).

CHEMICAL ENERGY BALANCE - EXAMPLE 11.4 : Calculate the bubble temperature T at P = 85-kPa for a binary liquid with x(1) = 0.4. The liquid solution is ideal. The saturation pressures are Psat(1) = exp [ 14.3 - 2945 / (T + 224) ], Psat(2) = exp [ 14.2 - 2943 / (T + 209) ] where T is in degree Celsius. Please take note that x(1) + x(2) = 1. Please take note that y(1) + y(2) = 1, y(1) = [ x(1) * Psat(1) ] / P, y(2) = [ x(2) * Psat(2) ] / P, * is multiplication. P is in kPa.

Am 18 year old I want to be cabin crew I have no experience in customer services how do I tell the interviewer am matured enough to take responsibility and challenges please some help me to answer outstanding answer

if you run the app program all vendor open items are cleared but is it possible to reverse the again again open items please tell me the answer

Yash Technologies,

ELECTRICAL TECHNOLOGY - EXAMPLE 16.1 : According to Shockley equation, the I - V characteristic of a diode is approximated by I = IS [ exp (nVD / VT) - 1 ]. For silicon, let the reverse bias saturation current IS as 0.000000000001. If n is ideality factor with value of 1.5, VT as thermal voltage drop of 0.026 V at room temperature, what is the value of current I that passes through the silicon diode in the heater of evaporator when the forward voltage drop VD = 0.026 V? Please take note that exp is the exponential function with e(1) = 2.718, e(2) = 7.389.