hi friends i have a problem.plz solve this.
i am working some where and i have the number of
swtitch.once my project manger says that we are going to
exapnd our number of employ so plz attech an another
switch.i asked to my jr network engineer that take a witch
and implemnt on that n/w,as he implement the switch on that
n/w.thats network get down,
plz tell me what is the reason of that.
- 2 Answers
- 3706 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / jitendera kuamr sinha
ok
it is very conceptual and simple.the cause of network down
when ever the jr.network engineer attch the raw switch it
was in server moade(by defaul every switch in the sever
made)so when ever we are going to connect the raw switch in
any short of n/w it shoud be made in client mode.thats the
cause that n/w get down
so simple na
jitendera kumar sinha
| Is This Answer Correct ? | 8 Yes | 3 No |
Answer / kittu
the cause of network down
when ever the jr.network engineer attch the raw switch it
was in server moade(by defaul every switch in the sever
made)so when ever we are going to connect the raw switch in
any short of n/w it shoud be made in client mode.thats the
cause that n/w get down
| Is This Answer Correct ? | 1 Yes | 0 No |
What is 10base2 ethernet lans?
Can we write any script for router to instruct that from where it will boots e.g. TFTP,FLASH...if yes what is it and how? 1 of my frnds says its possible...
Hi, All I am configuring EIGRP in Packet tracer, after configuring all the things it is not working but in one condition it is working fine if i am putting all my router and network withing one network subnets e.g. 172.16.0.0 or 10.0.0.0 but whenever i am puting different network subnets e.g. in one network it is RA(config-if)#=ip address 10.0.0.1, and in fa0/0= 192.168.1.10 and in RB(config-if)#10.0.0.2 (s1/0) and in S1/1 11.0.0.1 and in fa 0/0 192.168.100.1 ,where as in third router RC(config-if)#=ip address 11.0.0.2 and in fa 0/0 172.16.1.10 and after configuring all this serial is showing up and protocol showing up but eigrp process not taking place after adding eigrp configuration, i tried with "no auto-summary" command but not working.. Suggest me where i missing something? can mail me at : gtech.innovator@gmail.com
How many valid ip will b in /21 in route summarization?
What parameter is used with statically assigned routers to tell packets which interface to use to reach a distant network? A.) Mask B.) Subnet C.) Default gateway D.) Interface
Station A is transmitting data to station B, and expects an acknowledgment after every 400 bytes. After transmitting data for a while, the two stations determine the line is reliable and change to expecting and acknowledgement every 600 bytes. This is an example of (pick the best answer only): A.) BECN B.) Sliding Windows C.) Poison Reverse D.) Countdown timers E.) Split Horizon F.) Count to infinity
what is LAPB
Which of the following is a valid extended IP access-list? A.) router(config)# access-list 101 permit tcp host 172.16.30.0 any eq 21 log B.) router# access-list 101 permit tcp host 172.16.30.0 any eq 21 log C.) router(config)# acess-list 101 permit any any 172.16.30.0 D.) router(config)# access-list 101 permit ip host 172.16.30.0 any eq 21 log
Identify the type of hardware required to connect a Token ring network to an Ethernet network? A.) Repeater B.) TR-Enet C.) Router D.) Token Ring to Ethernet translation hub
Mention what command you must use if you want to delete or remove the configuration data that is stored in the nvram?
Although Cisco IOS 11.2 and later can auto-detect the LMI type in Frame Relay, which command will force the LMI type to q933a? A.) frame-relay lmi-type q933a B.) encapsulation frame-relay q933a C.) don't need to, it is the default D.) encapsulation q933a E.) encapsulation frame-relay type=q933a
What command do you use to disable domain lookup? A.) no domain-lookup B.) domain no-lookup C.) lookup no-domain D.) no ip domain-lookup
CCNA 
