Answer / jitendera kuar sinha

router and switch-
1st diffrence-router is a layer 3ree device where switch is
a layer 2 device
2-router understand ip adrees,where as in the switch in
understand harwair address.
3=this is the main diffrence which is the best as far as my
knowledege is conserned
switch break the collison domain and cretae smaller
collison doman where as router create single brodcast
domain at each interface,
switch cretae private dedicated collson domain and provide
independet bandwidth at each port
router and hub-
i have discribed router in first question
now in hub
hub is a also a L2 divice
hub have the property of
it is multiacess broadcast address
it is multo acess colisson network
it has single colission doman
it has single broadcast doman
hub doecnot create private deidcated collson domain and
doesnot provide independent bandwith at each port
hub and switch
hub is a
single brodcast domain
single coolision domain
whaer is switch is a multiple coolision doamin and single
broadcast doman.
switch create private dedicated collison domain and provide
dedicated bandwith at each interface.ulike hub
bridge and switch
bridge and swith both are L2 device
we can say that switch is a multiport bridge but there are
some diffrence

(1) bridge use softare to cretae and mange the filter
table.where as switch uses ASCIS to build and maintan there
table.bridges can have only one spaing tree whree as switch
may have many
(2)switches have more number of port then bridges
thanks
jitendera kumar sinha

Choose three reasons why the networking industry uses a layered model: A.) It facilitates systematic troubleshooting B.) It allows changes in one layer to occur without changing other layers C.) It allows changes to occur in all layers when changing one protocol D.) It clarifies how to do it rather than what general function to be done E.) It clarifies what general function is to be done rather than how to do it

1 Answers  

---

Brielfly explain the conversion steps in data encapsulation

0 Answers  

---

Why Clock rate command is not configured on ethernet interface of a router?

6 Answers  

---

Identify the 3 guidelines for routers in the same autonomous system? A.) Must be configured for RIP B.) Interconnected C.) Assigned the same autonomous system number D.) Configured for the same routing protocol E.) Must be same model of router

1 Answers  

---

What is the default IPX Ethernet encapsulation? A.) SNAP B.) Arpa C.) 802.2 D.) Novell-Ether E.) SAP

2 Answers  

---

Which port numbers are used by TCP and UDP to set up sessions with other hosts? A.) 1024 and above B.) 6 and 17 respectively C.) 1-25 D.) 6-17

6 Answers  

---

At which layer of the OSI model does the ping command operate? A. session B. network C. transport D. maintenance

12 Answers   EF, IBM, jetking, Nexlinx, Rkd, TCS, Wipro,

---

When setting up a WAN network, everything outside of the Demarc is not owned by the customer. Which of the following are not owned by the customer? A.) The T1 line. B.) LAN C.) The Router D.) DTE E.) PC's F.) CO

1 Answers  

---

In which protocol supenetting is enable by default?

0 Answers  

---

Explain the term 'multicast'.

0 Answers  

---

Which is true regarding half duplex Ethernet operation? A.) Half Duplex ethernet technology provides a transmit circuit connection wired directly to the receiver circuit at the other end B.) Half duplex transmission between stations is achieved by using point to multipoint Ethernet and Fast Ethernet C.) With Half Duplex transmission logically circuits feed into a single cable creating a situation similar to a one way bridge D.) Half Duplex transmission between stations is achieved using Point to Point Ethernet & Fast Ethernet

1 Answers  

---

What are the netbios and netbeui?

0 Answers  

---