What parameter is used with statically assigned routers to tell packets which interface to use to reach a distant network? A.) Mask B.) Subnet C.) Default gateway D.) Interface

1 Answers  

---

Name which protocols are link states?

0 Answers  

---

2. What are the valid ways to segment a LAN? (Choose all that apply) A. Repeater B. Bridge C. Switch D. Router

2 Answers  

---

I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used

5 Answers  

---

what is the reason for creating vlans

4 Answers  

---

As system administrator, you type "debug ipx sap" and receive the following lines as part of the IOS response: type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops What does "0x4" signify? A. That is a Get Nearest Server response. B. That it is a General query. C. That it is a General response. D. That it is a Get Nearest Server request.

2 Answers   Microsoft,

---

Which layer is responsible for negotiating data transfer syntax? A.) Network B.) Session C.) Application D.) Transport E.) Presentation

1 Answers  

---

Which command, that is used to test address configuration, uses Time-To-Live (TTL) values to generate messages from each router. A. trace B. ping C. telnet D. bootp

1 Answers  

---

Why we choose the router rather then L-3 Switch

8 Answers   Network Solutions, Wipro,

---

Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers  

---

What is the maximum hop count for Link-State protocols? A.) 15 B.) there is no hop count limit C.) 256 D.) 16

2 Answers  

---

Explain how many maximum paths you can give on latest ios in rip?

0 Answers  

---