You just entered the following command_Router(config#) line
console 0 Which operation is most likely to follow?
A. Confound terminal type
B. enter protocol parameters for a serial line
C. create a password on the console terminal line
D. establish a terminal type 4 connection to a remote host
E. change from configuration mode to console privileged mode
Answers were Sorted based on User's Feedback
Answer / bharghava srinivas
Ans: C
Reason :As in the Question it is mentioned as "LINE CONSOLE
0" it means it has entered into console mode,so we will
create password for the console terminal line....
| Is This Answer Correct ? | 10 Yes | 0 No |
Answer / bharghava srinivas
Ans: C
Reason :As in the Question it is mentioned as "LINE CONSOLE
0" it means it has entered into console mode,so we will
create password for the console terminal line....
| Is This Answer Correct ? | 8 Yes | 0 No |
Answer / surya mr
Dear i know it there will not be any username on Consol
port,That was enterred by mistake.
| Is This Answer Correct ? | 3 Yes | 0 No |
Answer / bharghava
dear Surya i don't think so, we won't create a user name in
console mode
| Is This Answer Correct ? | 3 Yes | 1 No |
Answer / bharghava srinivas
No Surya By Mistake U Should Not Keep,Bcoz So Many Guys Who
will Refer the Same Site May Confuse and asssume the
Same .......
So,Better When U R Posting an Answer "BE SURE"
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / surya
To create a username and password will enter into consol
mode,
| Is This Answer Correct ? | 1 Yes | 1 No |
Answer / rohit dodia
E. change from configuration mode to console privileged mode
| Is This Answer Correct ? | 2 Yes | 5 No |
Answer / rohit dodia
E. change from configuration mode to console privileged mode
| Is This Answer Correct ? | 0 Yes | 6 No |
Identify 3 characteristics of an IP address? A.) Contains a network portion and a host portion B.) 32 bits long C.) Unique to each network D.) Part of the default Cisco configuration E.) Referred to as the hardware address
What command displays only OSPF routes?
What is a digital certificate?
What is the command to manually enter a static route? A.) IP route network B.) IP route C.) IP route < destination network> D.) IP route
Which type of switching is considered to be 'wire speed?' A.) Cut-Through B.) Multiplexed C.) Inverted D.) Layer 4 E.) Store and Forward F.) Layer 3
How many hope count rip or rip2 can send updates?
PICT & JPEG are examples of what layer in the OSI seven layer model? A.) Transport B.) Presentation C.) Application D.) Datalink E.) Network F.) Session
Which network mask should you place on a Class C network to accommodate a user requirement of ten subnetworks? A. 255.255.255.192 B. 255.255.255.224 C. 255.255.255.240 D. 255.255.255.248
Using the access-list command, 'access-list 1 deny 2.2.2.2', what else must be done to stop host 2.2.2.2 from sending any traffic out of physical interface E0, while still allowing other traffic? A.) In global mode, Add a line - 'access-list 1 permit 0.0.0.0 255.255.255.255' B.) On interface E0, Add a line - 'access-group 1 in' C.) In global mode, Add a line - 'access-list 1 permit all' D.) On interface E0, Add a line - 'access-list 1 in' E.) On interface E0, Add a line - 'access-list 1 out' F.) On interface E0, Add a line - 'ip access-group 1'
Which global configuration command will tell the router to load the IOS file 'IOS_filename' from the Network File server at 1.2.3.4 during the next boot? A.) boot system flash IOS_filename 1.2.3.4 B.) boot system tftp IOS_filename 1.2.3.4 C.) config-register 0x0 1.2.3.4 D.) boot system rom 1.2.3.4 E.) This can not be done, only the first file in flash can be used.
What are the generic parts of a network layer address? A. an intenetworks number and a URL B. a vendor code and a serial number C. a network number and a host number D. a broadcast number and a unicast number E. a domain identifier and a device identifier
What is the beaconing?