What are three benefits of Integrated Services Digital
Network (ISDN) (Choose three)
A. PVCs are faster and more reliable
B. No specialized equipment is required
C. Data transfer is faster than typical modems
D. Call setup is faster than with standard telephone service
E. It carries many types of data tramp such as voice video
and data
- 1 Answers
- 6149 Views
- I also Faced
- E-Mail Answers
what is vlan
Which statement is true regarding Administrative distance? A.) It is a metric B.) Number of hops between two routers C.) Trustworthiness of the routing information D.) RIP Administrative distance is 100
Select the correct statements about PPP and SLIP for WAN communications? A. PPP uses its Network Control Programs (NCPs) component to encapsulate multiple protocols. B. PPP can only transport TCP/IP C. SLIP can only transport TCP/IP. D. SLIP uses its Network Control Programs (NCPs) component to encapsulate multiple protocols.
Which information must a router know in order to perform proper and pungent routing? A. destination application of an incoming packet B. number of other packets in a single flow of data C. destination network address of an incoming packet D. number of routers that also know a path to the destination
Can you explain PPTP (Point-to-Point Tunneling Protocol)?
hi shyam i am putting urs question here I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used
Which of the following is true? A. The default is to send debug output to the console screen. B. To view debug output from a telnet session, the "terminal monitor" command must be used C. If the "logging buffered" command is used, the debug output would be sent to RAM and can be viewed with the "show log" command D. If the "no console loggin" command were configured, output would besent to a telnet session E. All of the above F. None of the above G. A, B, and C. H. A, C, D, and E.
Hi Guys i hv one confusion. Need u peoples help. In EIGRP, maximum hop count is up to 255. By default only 100. Now question is - a) Suppose i hv a network consist of 115 routers & EIGRP routing protocol is configured. By default hop count is 100, so is there any manual configuration necessary for hop count ya router will automatically detect the hop count & will update the hop count accordingly..????? b) In EIGRP, Bandwidth & Delay is used to calculate metric. For this Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0 Now i want, Bandwidth & Load is used to calculate metric. For that wat i hv to configure & wat wub the metric weights. Cud anyone explain it plzzzz..!!!!
IP standard access lists use which of the following as a basis for permitting or denying packets? A.) destination address B.) port C.) protocol D.) source address
You are a network administrator and have been assigned the IP address of 201.222.5.0. You need to have 20 subnets with 5 hosts per subnet. What subnet mask will you use? A. 255.255.255.248 B. 255.255.255.128 C. 255.255.255.192 D. 255.255.255.240
As system administrator, you type "debug ipx sap" and receive the following lines as part of the IOS response: type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops What does "0x4" signify? A. That is a Get Nearest Server response. B. That it is a General query. C. That it is a General response. D. That it is a Get Nearest Server request.
What is the Difference between Hub and Switch?
CCNA 
