1. Categories >> Certifications >> Cisco Certifications >> CCNA
  2. Suggest New Category

Which command switches from User mode to Privileged mode?

A.) login

B.) privilege

C.) admin

D.) enable

E.) enter

F.) root

Question Posted / guest

Answers were Sorted based on User's Feedback



Which command switches from User mode to Privileged mode? A.) login B.) privilege C.) admin..

Answer / guest

Answer: D

Is This Answer Correct ?    6 Yes 0 No

Which command switches from User mode to Privileged mode? A.) login B.) privilege C.) admin..

Answer / surya

enable

Is This Answer Correct ?    6 Yes 0 No

Which command switches from User mode to Privileged mode? A.) login B.) privilege C.) admin..

Answer / jayakumar

enable

Is This Answer Correct ?    1 Yes 0 No

Which command switches from User mode to Privileged mode? A.) login B.) privilege C.) admin..

Answer / sanjeev

d

Is This Answer Correct ?    1 Yes 1 No

Which command switches from User mode to Privileged mode? A.) login B.) privilege C.) admin..

Answer / aashish bandawala

d) enable

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More CCNA Interview Questions

Identify 2 transport layer protocols? A.) IP B.) TCP C.) CDP D.) ARP E.) UDP

2 Answers  

What does the parameter -- LOG -- do on an IPX access list? A.) The log keyword is not a valid option. B.) Read the LOG to figure out what traffic to deny. C.) Logs the creation of the access list. D.) Logs IPX access control list violations whenever a packet matches a particular access list entry. E.) Ensures the IPX protocol places a log in the fireplace.

1 Answers  

Hi all of you, Actually this is interview qe? but i did,t do explain it completely so please give reply recently and completly Ans, what is sub-interface and inter-vlan ? And How to implement it on cisco router & switches and also which series router switches supported please write..........

2 Answers   Cisco,

Identify the command to view the configuration-register value? A.) show register B.) display config-register C.) show config D.) show version

1 Answers  

What is raid in ccna?

0 Answers  




Which statement is true regarding Administrative distance? A.) It is a metric B.) Number of hops between two routers C.) Trustworthiness of the routing information D.) RIP Administrative distance is 100

1 Answers   TCS,

What is true about frame-relay DLCI? A.) DLCI represents a single physical circuit B.) DLCI is optional in all frame-relay networks C.) DLCI identifies a logical connection between DTE devices D.) DLCI is used to tag the beginning of a frame with VLAN information

1 Answers  

Identify the 2 rules used when configuring a Distance Vector routing protocol? A.) Physically connected network(s) B.) Configure the classful address, no subnets C.) Enable CDP so neighbors can be detected D.) Configure all networks in Area0

1 Answers  

Which OSI Reference Layer controls application to application communication? A.) Datalink B.) Network C.) Transport D.) Session E.) Physical

2 Answers  

Which commands should you use to enable IGRP routing? A. router igrp 100 Network 192.168.1.0 Network 10.0.0.0 B. router igrp 100 Network 192.168.2.0 Network 10.0.0.0 C. router igrp 100 Network 192.168.1.0 192 168.1.1 Network 10.2.0.0 10.2.1.1 D. router igrp 100 Network 192.168.1.0 255.255.255.0 Network 10.2.0.0 255.255.255.0

3 Answers  

Which layer hides details of network dependent information from the higher layers by providing transparent data transfer? A.) Transport B.) Physical C.) Data Link D.) Session E.) Application F.) Network

5 Answers  

Identify 3 characteristics of ISDN? A.) Transports voice and data B.) Transports voice only C.) Support both BRI and PRI D.) Runs over existing phone lines E.) Same as X.25

1 Answers  

For more CCNA Interview Questions Click Here
Categories