What is true about frame-relay DLCI?
A.) DLCI represents a single physical circuit
B.) DLCI is optional in all frame-relay networks
C.) DLCI identifies a logical connection between DTE devices
D.) DLCI is used to tag the beginning of a frame with VLAN
information
Answer / guest
Answer: C
Data Link Connection Identifier (DLCI). A frame-relay
service provider
typically assigns DLCI values that are used by frame-relay to
distinguish between different virtual circuits on the
network. For the
IP devices at each end of a virtual circuit to communicate,
their IP
addresses are mapped to Dlci. Every DLCI value can have a
global or
local meaning.
| Is This Answer Correct ? | 3 Yes | 1 No |
Which two statements about IP RIP are true? (Choose two) A. It limits hop counts to 31 B. It is a link state routing protocol C. It uses autonomous system numbers D. It is capable of load sharing over multiple paths E. It uses bandwidth as the metric for path selection F. It broadcasts updates every 30 seconds by default
Which is true regarding store-and-forward switching method? A.) Latency varies depending on frame-length B.) Latency is constant C.) It is default for all Cisco switches D.) It only reads the destination hardware address before forwarding the frame
Does a bridge divide a network into smaller segments?
Which command can verify Application Layer connectivity between 2 hosts? A.) ftp B.) snmp C.) telnet D.) ping E.) traceroute
Given the configuration example<HR> <B>interface ethernet0 ipx network 4a ipx access group 800 out interface ethernet1 ipx network 3d interface ethernet2 ipx network 5c access list 800 permit 3d 4a</B><HR> Which two actions result from implementing this configuration? (Choose two) A. IPX network 5c will not receive any traffic B. Traffic from network 3d for network 4a will be forwarded out e0 C. Traffic from network 4a for network 3d will be forwarded out e0 D. Traffic from network 3d destined for network 4a will be forwarded out e2 E. The access list is applied to an outgoing interface and filters outbound traffic
Using the access-list command, 'access-list 1 deny 2.2.2.2', what else must be done to stop host 2.2.2.2 from sending any traffic out of physical interface E0, while still allowing other traffic? A.) In global mode, Add a line - 'access-list 1 permit 0.0.0.0 255.255.255.255' B.) On interface E0, Add a line - 'access-group 1 in' C.) In global mode, Add a line - 'access-list 1 permit all' D.) On interface E0, Add a line - 'access-list 1 in' E.) On interface E0, Add a line - 'access-list 1 out' F.) On interface E0, Add a line - 'ip access-group 1'
Put the following steps of encapsulation into the correct order: 1) The data is broken into segments to be organized 2) Frames are converted to 1s and 0s to be put on the wire 3) Packets are converted into frames 4) Information that users enter is converted into data 5) The segments are changed to packets to be routed A.) 4, 1, 3, 2, 5 B.) 4, 5, 1, 3, 2 C.) 2, 3, 1, 4, 5 D.) 4, 1, 5, 3, 2
What command do you use to disable domain lookup? A.) no domain-lookup B.) domain no-lookup C.) lookup no-domain D.) no ip domain-lookup
Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)# router igrp 100 Router(config-router)# network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0
Which command should you use to confound a router so that it can become a TFTP server host for a router system image that is run in a Flash? A. copy flash tftp B. config tftp server C. write, network -router name- D. tftp-server system -file name- E. setup server tftp -system name-
Explain how many types of ends in wan?
which utility should use to test whether TCP/IP has been initialized on a system.friends plz post the answer with explaination..