Interested to Buy Any Domain ? << Click Here >> for more details...
The coefficient of friction for the Asbestos-based materials used for clutch facing is a) 0.07 b) 0.17 c) 0.27 d) 0.37
1 3645The maximum amount of axial load to be applied on a clutch plate is a) 100 KN b) 200 KN c) 300 KN d) 400 KN
1552Mean effective radius of contact surfaces of a clutch plate is decided by a) Coefficient of friction b) Axial pressure c) Space available in the vehicle d) Amount of torque to be transmitted
1393Axial force to keep the clutch in engaged position is provided by a) Springs arranged circumferentially b) Pressure plate c) Flywheel d) Clutch pedal
1435The friction plate is always mounted on a) flywheel b) Pressure plate c) Internally splined hub d) Clutch spring
1606The main advantage of single plate clutch over cone clutch is a) Easier gear changing b) Less binding of contact surfaces c) Less pedal movement d) all of the above
1730The main function of transmission is a) To provide means to vary the torque ratio between the engine and the road wheels b) To provide neutral position c) To provide means to back the car d) all of the above
1542The resistance to the vehicle motion whose magnitude remain constant with respect to the vehicle speed is a) Resistance due to gradient b) Resistance due to the road c) Resistance due to the tyre friction d) all of the above
1569The resistance to the vehicle motion whose magnitude various with the square of the vehicle speed is a) Resistance due to gradient b) Resistance due to road c) Resistance due to the tyre friction d) Resistance due to wind
1310If the tractive effort is the highest for a given velocity, then the vehicle must be in a) Top gear b) Third gear c) Second gear d) First gear
2021The point of interaction of the tractive effort curve and the total resistance curve is called a) Stabilizing speed point b) Low speed point c) High speed point d) Normal speed point
1360If the given tractive effort curve and the total resistance curve does not intersect, then a) The vehicle will accelerate b) The vehicle will decelerate c) The vehicle will not be able to go at this gradient for the given gear d) None of the above
1238The main disadvantage of sliding mesh type of gear box is a) High noise level b) Low mechanical efficiency c) High skill required by the driver d) all of the above
1331Double declutching is used for the engagement of gears in a) Sliding mesh type of gear box b) Constant mesh type of gear box c) Synchromesh type of gear box d) None of the above
1330High speed gear is obtained in the case of sliding mesh gear box when a) Motion is transferred through the clutch gear to lay shaft gear b) Main shaft is coupled to the clutch shaft c) Smallest gear on the lay shaft is engaged d) Largest gear on the lay shaft is engaged
1343Post New Automobile Engineering Questions
Due to drive torque, what is transverse weight shift?
Explain different between two stroke engine four stroke engine?
Hi guys! I buyed this clone carprog but i realized that not reading 24cxx. I tried 93cxx and 25cxx and it read.But 24cxx not.I tried to put external power.Of course the eeprom was soldered out.The interface is new and never read 24cxx.I tried many 24cxx .Is there a solution for this problem? I read in other forum that need to replaced 74hc125D with 74hc125M 4 pieces. thanks!
What is a “proximity probe” used to measure?
Tell me about Bicycle rear wheel Sprocket working?
Is it mandatory to maintain RG Part 1 & 2 manually? Can we submit excel format of the same to excise dept?
Mean effective radius of contact surfaces of a clutch plate is decided by a) Coefficient of friction b) Axial pressure c) Space available in the vehicle d) Amount of torque to be transmitted
What is the allowable -ve crankcase pressure (vacuum) in the gas engine of 1.5 mw?
Can servomotor be used for applying torque or load to the gear box drive shaft at various speeds for gear box testing purpose.
Where is fan located in car?
Stiff spring is used in the selector mechanism a) To prevent engagement of two gears simultaneously b) To prevent engagement of reverse gear c) To facilitate the gear selection d) To avoid the necessity of having neutral gear
Will engine performance be damaged by mixing oil in fuel of four stroke bike ?
1.what is the minimum percentage for engineering students? I like to become RTO officier...please send me procedure for that...
If two shafts used for transfer of drive are inclined to each other, then a) Slip joint is used b) Flange coupling is used c) Universal joint is used d) None of the above
Define elastic limit and yield point.
