Answer / pragati sutar

Height of stanction should be about 1.2 to 1.5m (i.e same as
height of human being) so that operator can take reading of
transmitter easily.

Answer / vinoth kumar.n

maximum 1.2m to 1.5m standerd height for stancion
supports.because easy checking and maintanence purpose.

Answer / yousuf

the standard height of the stanchion is 1350mm to 1500mm.At
this height only the maintenance crew can easily view the
transmitter.
(saudi aramco standard is 1500mm)

Answer / va

1.2 meter or the height of the dispaly shpuld match the eye
sight of the operator/user.

Answer / raju b

Height of stanction 1.2 to 1.5 mtrs from the centre of the
instrument installed.

Answer / toji james

The standard height of a stanchion support is a 1.5 meter
exactly.....

Answer / thomas

Hey sorry this is a query regarding the same matter.
Why is it 1.3 to 1.5 lower than the average ht of an operator, will this be helpful for maintenance.

Answer / ngb

1.2M FOR ALL STANCION ITS STANDARD

Answer / bert

Base on experience in a construction company, we mount the
stanchion support for any of the instruments on field, it
should be mounted at the height of 4.2 feet and it should
be free for all any obstruction for maintenance crew.

Answer / sridhar

The height of stanchion is a 1.5 mtr due to if any
pressure,level tranx get any leakeage,that time no any
accident accour in eye face area

Convert a pressure, level, flow, or temperature process variable value into the appropriate pneumatic or electrical value given different types of instruments.

6 Answers   Jindal, MCL, Thermax,

How do you identify between actual alarm and false alarm in a Temperature Transmitter in SCADA based Control System

0 Answers  

what is instrument termination

1 Answers  

What is Cavitation in a control valve?

0 Answers   CCIE, KN,

i have one tank of 500mm height, which is in under vacuum of 735 mmHg, I want measure level of the same using DPT , SO WHAT WILL BE THE URV & LRV, DENSITY OF THE TANK FLUID IS 0.95. is there necessary to fill the LP side with fluid.

7 Answers  

Why ac supply load cell is used? Can we use the dc supply load cell?

0 Answers  

Where & Why we are using SURGE PROTECTION ?

4 Answers   IOCL,

What for barriers are used in DCS & PLC systems?

2 Answers  

How can you differentiate Instrumentation to Electrical?

1 Answers  

(1) In turbine, what does term CDP, NI, NH, HSSOC, means. (2) What is the purpose of LO overhead tank in turbines.(3) An equipment is certified for EEX, IA, IIC,T6, what do you under stand by this.(4) what is SURGE, and how it is prevented, what is the purpose of bypass valve across AS valve.(5) Give 2 application of quartz crystal used for process parameter measurement.(6) what is meant by cold float of compressor shaft. (7) state four different types of flow measurement. For gas flow measurement mmscfd is the common unit. Expand the unit and specify significance of word S in the unit.(8) what is meant by Gap voltage, in vibration measurement. Normally how much Gap voltage is set and state the reason.(9) what will the new flow factor if D/P transmitter is Re-Ranged from 25” wc to 50” wc.(10) what is the usage of QDV & Volume booster.

0 Answers   ADMA OPCO,

1,why we use 4-20 ma output of all instrument qhy not use 0- 20, 2,what is the different between PLC & DCS. 3,how can we meaure maximum span of new flowmeter if not given any information.

4 Answers   Reliance,

if conical type tank in top LEFT side solid material coming but LT MOUNTED IN TOP OF LEFT SIDE, how to measure ultrasonic level transmitter ?

1 Answers   Cairn,