when ever we apply show flash comand on the router it
givesthat informatin
router#show flash
syatem file directory:
file length name/status
1 8121000 c2500-js-L.112-18.bin
what does it nean
plz help
i have read it from book but not bale to understand
i am looking towards u for the help
- 1 Answers
- 3626 Views
- IBM, I also Faced
- E-Mail Answers
Answer / jitendera sinha
ok i am jitendera kumar sinha a cisco certified network associate(ccna) i am trikng to explain that may be i wong but let me try to explain
ok
this number is non thing it is a simple file name
now i am going to derived it
c2500-it is platfrom
j indicates that file is an enterprise image
s indicate that file cnatain eated capablity
l indicates that file,can be moved from falsh memory if nedded.
112-18(wrong syn) i think it must be 11.2-18 it is a revision num
bin indicates that cisco ios is a binary executable file
| Is This Answer Correct ? | 0 Yes | 0 No |
When should you apply SAP filters to Netware service advertisement messages? A. When services are not required for a particular area or network B. Only after service advertisement messages have flooded the network C. Before any type of router convergence takes place D. When no change in network services has taken place for 40 minutes
What protocol advertises Netware services to network clients? (Type acronym).
Match the following devices with the correct description. A. Switch 1. Operates at the physical layer and extends the cable as if it is a single cable. B. Router 2. Operates at the physical layer and connects all connections into one device or concentrator. C. Repeater 3. Operates at the network layer and can filter both hardware and network addresses. D. Hub 4. Works at the Data-Link layer and transmits a digital signal only to the specific port where the destination MAC address is located.
5. Which Two Settings must be configured in order to use the GUI to configure Call Admission Control with voice Applications
How can I release the restriction of CISCO2811C/K9? 10M optical fiber, Speed limit of 125kb / s, made by last network administrator, how can I release the restriction? Please tell me the detail, thanks! Cisco configuration： CISCO2811C/K9 ! ! ! ! ! ! ! interface FastEthernet0/0 description WANpork ip address x.x.x.x 255.255.255.248 ip access-group 110 in no ip proxy-arp ip verify unicast reverse-path ip nat outside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet0/1 description LANpork ip address 192.168.x.x 255.255.255.0 ip access-group 101 in no ip proxy-arp ip verify unicast reverse-path ip nat inside ip virtual-reassembly rate-limit output 1000000 1000000 1000000 conform-action transmit exceed-action drop duplex auto speed auto !
Which Of the Statements best describes VPLS ?
What are metrics used with IGRP? A. Ticks B. Load C. Hops D. Delay
Diagramming application information flow is important because: A. it helps identify heavy traffic paths B. it helps figure out why email gets from one place to another C. it can tell you when to purchase a new router D. it can tell you when to purchase a new switch
Which of the following does not specify an application requirement that affects your network design? A. The number of users B. The peak hours that the applications are used C. The types of applications used D. Security risks
Which of the following is not true in regards to route summarization? A. It increases the size of the routing table B. It increases the complexity of the network C. IP networks must be contiguous to be safely summarized D. Routing tables must have the capacity to support classless routing
Match the following routing techniques with the correct descriptions: A. Static Routing 1. Mandatory configuration B. Dynamic Routing 2. No route updates 3. Can better tolerate failures 4. Sends update when topology changes 5. Path is determined by the router 7. Traffic is reduced
difference between layer 3 switch and router
0 Answers Aptron, Tech Mahindra,
CCNA 
