1. Categories >> Engineering >> Instrumentation
  2. Suggest New Category

In a class of 150 students, 40 passed in Social Studies, 90
passed in Science and 30 failed in both the subjects.
vi)How many students passed in at most one subject among
Science and Social Science?

Question Posted / guest

Answers were Sorted based on User's Feedback



In a class of 150 students, 40 passed in Social Studies, 90 passed in Science and 30 failed in bot..

Answer / wteva

110

Is This Answer Correct ?    30 Yes 4 No

In a class of 150 students, 40 passed in Social Studies, 90 passed in Science and 30 failed in bot..

Answer / heri

120 passed in both the subjects

Is This Answer Correct ?    12 Yes 8 No

In a class of 150 students, 40 passed in Social Studies, 90 passed in Science and 30 failed in bot..

Answer / charles

90

Is This Answer Correct ?    2 Yes 0 No

In a class of 150 students, 40 passed in Social Studies, 90 passed in Science and 30 failed in bot..

Answer / kapil

120 student passed in at most one subject

Is This Answer Correct ?    4 Yes 3 No

In a class of 150 students, 40 passed in Social Studies, 90 passed in Science and 30 failed in bot..

Answer / samir

10 student

Is This Answer Correct ?    10 Yes 10 No

In a class of 150 students, 40 passed in Social Studies, 90 passed in Science and 30 failed in bot..

Answer / abdullah marimar del toro

9,962 students!

Is This Answer Correct ?    1 Yes 7 No

In a class of 150 students, 40 passed in Social Studies, 90 passed in Science and 30 failed in bot..

Answer / amar

105

Is This Answer Correct ?    4 Yes 15 No

Post New Answer

More Instrumentation Interview Questions

capillary type tranmitter using remote seals and capillary tubes filled with liquid of known of known density so if you wanna callibrate it just close block valve just before capilary @ high side & connect druck apply it's calibrated range pressure as normal calibration ensure low side block valve must be closed & if you asking commissioning so this is not a DP type pressure tx so simple if you wanna put in servie this tx just open high side block valve & than low side block same way i do it but still transmitter showing -13 ma.just tell me what i want to do ?

1 Answers   Gasco,

IF TX SHOWS SLOW RESPONSE, WHILE A CLOSE LOOP AND WHEN WE PUT THE CONTROLLER ON MANUAL THE PROBLEM RECTIFIED, SO WE CAN SAY THE PROBLEM IS IN

1 Answers   IFFCO,

Good Evening all.My question is - For a feed water line to an equipment if i need to measure the flow we will use orifice /magnetic/vortex depend on cost/spec.If i need to measure a ''Alarm''signal and ''Interlock'' from one point i think we can use orifice type in one location with 2 different tapping points - one for alarm and one for an interlock to flow valve..If in case i need to have both these signals(Alarm & interlock) from magnetic flow meter,is it possible??will 2 seperate sensors will be located inbuilt r we can program it ??..i thk we can have one transmitter with these 2 signals...need to know any technical issues are there?pls clarify

3 Answers  

suppose there is gas flow meter I want to know weather meter calibration is done at high pressure or low pressure? pls justify.

2 Answers   Siemens,

what is protonics how it is differ from electronics

1 Answers  




Explain why use mmwc unit?

0 Answers  

warning lamp does not light, but it does light when the wire from the lamp going to the sending unit is grounded (the part that plugs into the sending unit) what does this indicate)?

1 Answers  

What is Actuator?

3 Answers   Descon,

GWR radar transmitter working principle?

2 Answers   Tata Steel Limited,

In s7-200 we use HMI TD-200C , what that C stands for........ plz reply

2 Answers  

Could anybody tell how much amps will a single input to plc will consume?

1 Answers  

How to Calibrate Vibration Probe (Axial, Redial) in field

0 Answers  

For more Instrumentation Interview Questions Click Here
Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)