Answer / ganesh

you cannot shutdown a cisco router through command line
interface instead you can restart it.

Answer / ataro

Cisco router runs the image from flash to memory not from
Hard Disk. So shutdown command is not required, just pull
the power cable.

Answer / vinay

hi hitesh

thanks for you response ......

in the about question i am asking about how can we shutdown
router or switch using windows command prompt...not with
telnet are ssh etc

i think we cant do such type of things using windows cmd....

thanks in advance

Answer / harish kumar

Router can't be shutdown from command prompt. Due to its
power button.

Answer / parshant

vinay
you can shoutdown router without power off with the help of
power manger. you need to configure your ups

Answer / vinay

hi hitesh

thanks for you response ......

in the above question i am asking about how can we shutdown
router or switch using windows command prompt...not with
telnet are ssh etc

i think we can't do such type of things using windows cmd....

thanks in advance

Answer / john

the command is reload not reboot

Answer / jitendra kumar patel

Hi,

The command to restart the router using command line interface is " reload" without quotes. However there is also a command as "restart" and there is a subtle differences between both. Reload basically does the cold reboot and yes one need to check the logs to conclude if previous shutdown was intentionally or due to power outage.

--cheers

Answer / vinayybx

how can we restart the router using command line interface

syntax : ?????

Answer / hariharan

i don't know cisco router configuration

but may be able to LED Position off(0) command

if LED position off (0) router fan may stop and then

router shutdown mode

please try it

Hi, gys i am Hasnain alamI want to get certification how do it ? please sugges me.

1 Answers   IBM,

What type of Ethernet operation allows only one entity to transmit at a time? For example, if someone else is transmitting, they must wait. A.) Full-Duplex B.) Dual-Duplex C.) Half-Duplex D.) Latex E.) Quarter-Duplex F.) Suplex

1 Answers  

Which command would show all Ethernet interfaces with IPX configured on them? A.) show interface ipx ethernet B.) show ipx interface C.) show ipx interface ethernet D.) show ipx E.) show version F.) show run

1 Answers  

To monitor ipx traffic on a network, what command would you use? A. debug ipx transaction B. show ipx traffic C. show ipx events D. display ipx traffic

3 Answers  

1 what is private vlam 2 if there is a router which have two fast Ethernet from from fa0/0 192.168.10.0/24 network is connected from fa0/1 192.168.20.0/24 network is connected all bacsic routing is done will they communicate 3 what is difference between snmp v1 v2 and v3 what difference between name and stranded access list

2 Answers  

Ping uses which Internet layer protocol? A.) RARP B.) ICMP C.) ARP D.) FTP

3 Answers  

What does the acronym ARP stand for? A.) Address Resolution Phase B.) ARP Resolution Protocol C.) Address Resolution Protocol D.) Address Recall Protocol

2 Answers  

Which layer is responsible for negotiating data transfer syntax? A.) Network B.) Session C.) Application D.) Transport E.) Presentation

2 Answers  

What is the default LMI type for Cisco Routers that are using Frame-Relay? A.) Gandalf5 B.) Q933A C.) Cisco D.) IETF E.) ARPA F.) SAP

2 Answers  

Explain the difference between routing and routed protocols?

0 Answers  

If there is only 2 host in bus topology is that possible collision accord?

0 Answers  

hi friends i have some problem regarding technical round ahr round plz tell me what should the right answer technical questions 1 what is brouter 2 what is the menaing of 10 base2, 10 base 5 and 10baset 3 what is diffrence between bit rate and baud rate. and this question was tooooooooooo much difficult to me that hr said to me that rank me after the taking the all short of interview

5 Answers