Answer / moody

electrical train works with electrical drive " asystem
consists of motors , gears and belts "
the type of motor used is direct current motor or exactly
dc series motor becas it has high starting torque for
moving the train from the stationary state

Answer / p.silamparasan

First the train receive 25KV supply from the overhead
transmission line and it step down and converts it into D.C
voltage. And given to D.C series motor. Because the motor
needs heave starting torque to move the stationary train.

Anybody kindly give e a feedback.

Answer / ashokreddyreguri

Motors used for electric trains are 3-phase induction
motors,DC series motors
3-phase induction motors- from the sub sstation the supply
is 25 KV or 33 KV.Loco consists of a step down transformer
where this 25 or 33KV is stepped down to 750 v to 1500 v.
DC series motors -600 v dc
force or torque is tansferred from motor shaft to pinion,
gear wheel,driving wheel.

Answer / prakash

Electrical train works by DC series motors.25Kv supply is
used

Answer / guru

Electric Trains work on DC Series motors

The Overhaed supply is 25kV AC supply. It is step down and
rectified to use at DC supply

Answer / bhanu

Electric train runs by using either DC Series Motor or 3-
phase Induction motor
the train receives 25kv voltage, transformer in it steps
down the voltage to 600v ac and then converted to dc for dc
series motor and 750v ac for induction motors.

Answer / oovii

Basically, DC series motors are employed in electrical train
on Traction. It uses DC series Motor because it has high
starting torque and good speed regulation.

Here overhead supply is used 25KV AC. First it step down and
then converted into 750V DC which is applied to DC Series
Motor.(Some area uses 1.5KV DC in overhead)

when a train get start it uses series connection of 2 or 4
series motor. It provide high torque.

After starting, it uses parallel connection for high speed
and less torque

Answer / dileep gopalakrishnan

train use dc series motor...the 25kv 1phase catenary is
stepdown and converted to dc.......this dc supply is given
to dc series motor........

Answer / ranjan

Train uses the d.c series motor.An electric train recive
25*1000v from the overhead lines which voltage rectifi(step
down) by the transformer to 600 a.c voltages which further
convert to d.c voltage bcoz d.c series motor for starting
torque high.

Answer / karthickraj

most probably we use dc series motor .because in dc starting
torque is maximum. so that it is efficient to start up the train

What is the power requirement of tamil nadu for one month?

0 Answers  

is all the servo motors having brake?please specify which servo motors having brake for stop on position and which are not.

0 Answers  

what is idmt relay

1 Answers  

What are the implications when the power factor is is leading condition ?

1 Answers  

Hello friends, Can anyone explain the concept of zones in Bus bar protection and how can we differentiate the main zone and check zone in Bus bar protection

1 Answers   ABB, NCC,

What is the difference between indoor and outdoor transformer

0 Answers   Ama Airfield Lighting System,

From stability point of view,What(higher/lower) should be the value of inertia constant of rotating machines?

1 Answers  

what is the voltage between earth & neutral in 3 phase electrical connection.

0 Answers   Megatron Solutions, SIPL,

why in a transformer frequency remains constant? if frequency is changing what will happen?

5 Answers  

If a surge divertor is required to be protected by 32 amp C Curve Circuit breaker does this limit the amount of protection from surges that you will acheive

0 Answers  

What is meant by regenerative braking?

5 Answers  

why u want to work in sail/ntpc as u r already in an it company where life is good, good environment no much tensions etc?

6 Answers   Sail,