Answer / salam

Corrosion occurs where levels of oxygen or carbon dioxide
are high, where ph values are low, where contact occurs
between dissimilar metals and in damp environment.

Erosion is a mechanical wearing away of metal or other
material by impingement of ash particles or a cutting of
the metal.

Answer / msv chaitanya

CORROSION IS A CHEMICAL LOSS

EROSION IS A MECHANICAL LOSS

Answer / guest

Corrosion means the chemical reaction resulting material
loss through oxidation or sulphites. For example rust
(FeO2) etc. But Erosion is physical / mechanical material
loss due to continuous action. For example Big rocks are
being cut by water falls, with a thin wire we can cut any
thickness metal.

Answer / abdul hameed

Corrossion:Chemical reaction weaken the material and turns
to is ore.

Erosion:Weaken the material due to abrassive action of
suspended particles at high velocity.

Answer / v.suresh

Corrosion occurs where levels of oxygen or carbon dioxide
are high, where ph values are low, where contact occurs
between dissimilar metals and in damp environment.

Erosion is a mechanical wearing away of metal or other
material by impingement of ash particles or a cutting of
the metal.

Answer / faruq

corrossion: The chemical or electrochemical reaction
between a material, usually a metal, and its environment
that produces a deterioration of the material and its
properties.

erosion: The act or operation of eroding or eating away

Answer / manveer singh (honey)

1. Corrosion is a chemical process.
Erosion is a physical process.
2. this is a process of slow.
this is a process of fast.
3. it normally happens because of chemical
reaction.
it occurs by chemical reaction

Answer / hari

corrosion is a chemical reaction which can only distroy the ferrous materials(ferro-metals).But non-metals it can't.

In case of erosion it just not limited for ferrous or non ferrous metals because it is a mechanical action(loss) which can distroy any contacting surfaces too for a while.

How many types of fits are there?

0 Answers  

when a solid shaft is subjected to tension its linear dimension changes equaly as its lateral dimension,then what will be its poissons ratio?

7 Answers   Crompton Greaves,

how to work on angular contact bearing? And which type load it take.

2 Answers  

What are the causes of failure of boiler tubes ?

0 Answers  

Gearpump is running but discharge valve is closed so, what difficulty in pump?

1 Answers  

what is ton(refrigeration)?

2 Answers  

25 questions in 25 minutes were asked by L&T corein mechanical engg test on 28 nov 2011 are as follows:- L&t mechanical consists of 1> airfuel ratio 2> mollier chart for flow rate 3>homogeneous or hetreogeneous mixture 4>sublimation curve 5>effect on room temperature when fridge is opened 6>cop of refrigerator 7> punching and piercing uses shear or not 8>method not used for tapering 9>forming method not used for productn 10>numerical regardng no.of cuts 11>flow of chip is controlled by which parameters 12> property important for impact loading 13>stifness of spring when it is cut into 2 pieces 14> device reqd for energy fluctuation 15> property on which rivet is selected 16>crowning to prevent flat belt pulley errors like undercut 17>cavitation occurs at which stage 18>qstn regardng inventory control 19>for ship vessel industry what sort of plantlayout reqd 20>value engg definition 21> qstn on how the extnsn occurs for uniform loading 22> qstn regardng stress actng on the shaft23>maximum value of mohr's circle diameter 24>qstn regardng meshing of teeth 25>qstn on helical gear reqrd better read G.K.PUBLISHERS GATE PAPERS ESPECIALLY FROM 1993 to 2003 ESPECIALLY THEORY QUESTIONS RATHER THAN NUMERICAL QUESTIONS

0 Answers   L&T,

What are the causes of damage to propellers?

0 Answers  

What is the difference between Maintenance Order and Production Order. the point is i want to know the affection of Movement type 261 thru maintenance order and Production order. if i change any settings for Maintenance order it will affect to production order process also for 261 movement type ?

0 Answers   Saudi Ceramics,

how hydraulic power stearing & clutch work plz explain?

1 Answers  

Pipe Lin Question

1 Answers   Reliance,

How much is 1 kn in kg?

0 Answers