Answer / ravi pratap singh

In the technical universities such like IIT AIEEE AND STATE GOV TECHNICAL UNIVERSITIES PROVIDE B.Tech Degree and the universities which have the art science along with engineering department provies B.E degree. there are not so big diffrence in syllabus of both b.e and b.tech

Answer / solanki chirag

i find that the major difference between them, is only suffix tech and .e
because all books ,all courses are same but only students study under expert teacher .....
and talking about them technical thing so technical knowledge also offered by industry ...in our training period .........

Answer / rajesh kumar

b tech in che engg is more concerned  to practicals,whereas in BE it is more concerned to theoretical

why GOD ALMIGHTY has made every living thing by water?

5 Answers  

---

GENETIC ENGINEERING - EXAMPLE 27.4 : According to Hardy-Weinberg Equation, p x p + 2 x p x q + q x q = 1 where p = dominant allele frequency and q = recessive allele frequency. Let p + q = 1. Fraction of population has 2 copies of the p gene = p x p. Fraction of population has 2 copies of the q gene = q x q. Fraction of population has a copy of p gene and a copy of q gene = 2 x p x q. In a small town, the allele frequency is q = 0.2 for a recessive gene, the delta-32 mutation, that gives human protection from HIV infection. (a) Find the allele frequency of a dominant gene, p. (b) What percent of the population has at least a copy of the gene that cause the population either immune to HIV or less susceptible to the disease?

1 Answers  

---

SSR meanig

1 Answers  

---

how to decide reflux ratio & its calculation

1 Answers  

---

What is the angle of repose?

0 Answers  

---

THERMODYNAMIC - EXAMPLE 10.3 : According to Raoult's law, the pressure when vapor is completely condensed, P = x(1) P(1) + x(2) P(2) ... + x(n) P(n) when x(1), x(2) ... x(n) are the mole fractions of component 1, 2 ... n and P(1), P(2) ... P(n) are the vapor pressures of component 1, 2 ... n. A vapor at 74 degree Celsius containing 70 mole % water and 30 mole % ethanol is to be completely condensed. At the temperature of 74 degree Celsius vapor pressure is 0.38 atm for water and 0.97 atm for ethanol. What is the minimum pressure the compressor must be operated?

1 Answers  

---

What are advantages using hollow shaft impeller?

0 Answers  

---

Question 69 - A well delivers 225 US-gallons per minute of water to a chemical plant during normal system operation. (a) Calculate its flowrate in the unit of mega US-gallon per day or MGD. (b) The following formula is written next to the chlorine feed point : (chlorine feed rate, lb / day) = (flowrate, MGD) X (dose, mg / L) x (8.34). If this formula is correct, then what should the chlorine feed rate to be in pounds per day (lb / day) if the desired dose is 2 mg / L. (c) Prove by calculations that the constant 8.34 in the formula next to the chlorine feed point is correct. Let 1 US-gallon = 3.78541 L and 1 mg = 0.0000022046 pound.

1 Answers  

---

We are having proplem with the persperation smell in ETT/ECHO room in our cardiac hospital.The 2 Ton of AC is not conditioning the environment. We have to use exhaust fan to through out of the room bad air. Could anyone suggest how to coup with this effectively using chemical engineering. Any permanent solution to neutralise the bad smell.The Air freshners are not doing enough instead making a bad odour.

0 Answers  

---

NATURAL GAS ENGINEERING - QUESTION 26.2 : (a) The Hyperion sewage plant in Los Angeles burns 8 million cubic feet of natural gas per day to generate power in United States of America. If 1 metre = 3.28084 feet, then how many cubic metres of such gas is burnt per hour? (b) A reservoir of natural gas produces 50 mole % methane and 50 mole % ethane. At zero degree Celsius and one atmosphere, the density of methane gas is 0.716 g / L and the density of ethane gas is 1.3562 mg / (cubic cm). The molar mass of methane is 16.04 g / mol and molar mass of ethane is 30.07 g / mol. (i) Find the mass % of methane and ethane in the natural gas. (ii) Find the average density of the natural gas mixture in the reservoir at zero degree Celsius and one atmosphere, by assuming that the gases are ideal where final volume of the gas mixture is the sum of volume of the individual gases at constant temperature and pressure. (iii) Find the average density of the natural gas mixture in the reservoir at zero degree Celsius and one atmosphere, by assuming that the final mass of the gas mixture is the sum of mass of the individual gases. Assume the gases are ideal where mole % = volume % at constant pressure and temperature.

1 Answers  

---

Name some guidelines for designing for liquid and gas velocities in process plant piping?

0 Answers  

---

ENGINEERING MATHEMATICS - EXAMPLE 8.3 : Solve the first order differential equation : (Z + 1)(dy/dx) = xy in term of ln |y| = f(x). Z = (x)(x).

1 Answers  

---