1 Cubic Meter = 487 Modular Brick, 1 Cubic Meter = 494 Non
Modular Brick, (As per Rate Analysis DSR 2012 Vol.-1)what is
the Brick Size ?
1 Cubic Feet = 13 Modular Brick, 1 Cubic Feet = 17 Non
Modular Brick. what is the Brick Size ?

Answers were Sorted based on User's Feedback



1 Cubic Meter = 487 Modular Brick, 1 Cubic Meter = 494 Non Modular Brick, (As per Rate Analysis DS..

Answer / shinu

* Modular Brick Size - 200mm X 100mm X 100mm
* Non Modular Brick Size - 229mm X 114mm X 70 mm

Is This Answer Correct ?    6 Yes 2 No

1 Cubic Meter = 487 Modular Brick, 1 Cubic Meter = 494 Non Modular Brick, (As per Rate Analysis DS..

Answer / nikhil

Modular Brick Size = 190 x 90 x 90 mm
With addition of plaster it counted as 200 x 100 x 100 mm
For 1 Cum :-
1 brick quantity including plaster (in CuM)
= 0.2 x 0.1 x 0.1 m
= 0.002 CuM
Total bricks in 1 CuM = 1/ 0.002
= 500 Nos.

Is This Answer Correct ?    1 Yes 0 No

Post New Answer

More Civil Engineering Interview Questions

How much Pressure will apply in Water proofing Grouting method to fill the crack in beams or slabs?

2 Answers   GMC,


what is the proportion of M25 geade cincrete.?

16 Answers   Adani, L&T,


please send the model qn paper of jindal steel power in civil engineering..

1 Answers  


What is the permissible limit of silt contain in sand for rcc Work?

7 Answers   Ambuja,


How to replace dia of bar in beam like 25mm 3no.S at bottom But due to some reason on site 25mm bar is not available Then is it ok to provide 20mm 4no.S? Give description or Formula to calculate area of steel and replacement?

3 Answers  






what is difference between 33, 43 and 53 grade cement..? which is more suitable for construction and why,..??

3 Answers  


density of crush sand & crush stone or grit powder

0 Answers   Godrej, L&T,


asubmerged weir is one in which the water level on the down stream side of the weir is just at the crest level below the crest level above the crest level at stamp elevation as water surface on upstream

0 Answers  


How much quantity of cement and sand required for the inlining of 610mm dia MS pipe 8.7mm thk.Inlining thickness is 10mm and CM ratio is 1:1.5.

0 Answers   IVRCL,


PLS.......... ANY ONE CAN FORWARD ME PREVIOUS QUESTION PAPER hpcl civil engg

0 Answers   HPCL,


Dear Sir What is the Contraction joint for base Slab

0 Answers   L&T, TES,


how much cement is consumed by a stone masonry wall 17.7m long,0.55m wide and 1m high

0 Answers   Ministry of Agriculture,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)