Answer / astha shukla

density of petrol is 737.22kg/cu m because its density is depands on a whole range of factors including purity and temp.

Answer / suraj chaudhari

Density of pure gasoline is ranges from 690-710 kg/cu m. and above that there is a density of the diesel and kerosene has the density 750kg/cu m.

Answer / srk

Density of petrol is 0kg/cu m.

significance of fouling factor in shell and tube heat exchnager

1 Answers  

---

PETROLEUM ENGINEERING - QUESTION 25.2 : (a) The American Petroleum Institute gravity, or API gravity, is a measure of how heavy or light a petroleum liquid is compared to water. Let SG = specific gravity of petroleum liquid, and V = barrels of crude oil per metric ton. Given the formula for API gravity = 141.5 / SG - 131.5 and V = (API gravity + 131.5) / (141.5 x 0.159), find the relationship of SG as a function of V. (b) An oil barrel is about 159 litres. If a cylinder with diameter d = 50 cm and height h = 50 cm is used to contain the oil, find the volume V of the cylinder in the unit of oil barrel by using the formula V = 3.142 x d x h x d / 4. (c) First reference : 1 cubic metre = 6.2898 oil barrels. Second reference : 1 cubic metre = 6.37 oil barrels. What are the 2 factors that cause the difference in such reference data?

1 Answers  

---

Question 109 - (a) Acceptable wavefunction in quantum mechanics in the range of : negative infinity < x < positive infinity, vanishes at least at one boundary. Which of the following is the wavefunction or are the wavefunctions of acceptable theory : P = x, P = | x |, P = sin x, P = exp (-x), P = exp (-| x |)? State the reason. (b) Let linear momentum operator P = -ih d / dz. The wavefunction is S = exp (-ikz) where i x i = -1, k and h are constants. Find the linear momentum of such wavefunction by using the term P x S.

1 Answers  

---

PROCESS CONTROL - EXAMPLE 6.3 : The differential equation is 3 dy / dt + 2y = 1 with y(0) = 1. (a) The Laplace transformation, L for given terms are : L (dy / dt) = sY(s) - y(0), L(y) = Y(s), L(1) = 1 / s. Use such transformation to find Y(s). (b) The initial value theorem states that : When t approaches 0 for a function of y(t), it is equal to a function of sY(s) when s approaches infinity. Use the initial value theorem as a check to the answer found in part (a).

1 Answers  

---

What types of valves are recommended for slurry services?

0 Answers  

---

what is fund flow definition

1 Answers   Amara Raja,

---

can you explain about the design calculations and procedure of boiler

0 Answers   Reliance,

---

A cantilever beam of length L = 3 m carries a uniformly distributed load (UDL) of W = 20 N / m throughout the length. Calculate the bending moment, BM of the beam near the fixed end. What is the shear force, SF at this point? Let SF = -WL, BM = -LWL/2.

1 Answers  

---

how to convert Nm3/hr to Kg/hr for air, @ 10.4 kg/cm2.g dischare pressure, does density doesn't affect on calculation?

1 Answers  

---

What are the most common problems encountered in a valve or bubble cap distillation column?

3 Answers   Eastman Chemical,

---

NATURAL GAS ENGINEERING - QUESTION 26.1 : (a) In natural gas pipe sizing, the length of the pipe from the gas source metre to the farthest appliances is 60 feet. The maximum capacities for typical metallic pipes of 60 feet in length are : 66 cubic feet per hour for pipe size of 0.5 inches; 138 cubic feet per hour for pipe size of 0.75 inches; 260 cubic feet per hour for pipe size of 1 inch. By using the longest run method : (i) Find the best pipe size needed for the capacity of 75 cubic feet per hour. (ii) Estimate the suitable range of capacities for the pipe size of 1 inch. (b) The maximum capacities for typical metallic pipes of 50 feet in length are : 73 cubic feet per hour for pipe size of 0.5 inches; 151 cubic feet per hour for pipe size of 0.75 inches; 285 cubic feet per hour for pipe size of 1 inch. By using the branch method find the best pipe size needed for the capacity of 75 cubic feet per hour when the length of the pipe from the gas source metre to the appliance is 52 feet.

2 Answers  

---

respected sir,i have been selected in the written examination(CHEMICAL) of IOCL Panipat held on 30 m1rch, So please tell me which type of questions asked in this interview frequently.Can u mail me some questions?

22 Answers   HCL, HCPL, HPCL, IOCL,

---