To find closed tank level by DP transmitter , how to
findout its range.and insomeplace they using range like -
1500 to +1500 mmwc why not 0 to 3000 mmwc. how they spilit
they range for minus and plus.and why?



To find closed tank level by DP transmitter , how to findout its range.and insomeplace they using ..

Answer / yashwant

THIS IS LEVEL MEASUREMENT USING DP TRANSMITTER, CLOSE TANK
MEANS PRESSURIZED ,PRESSURE IS EVERY WHERE IN SIDE TANK WILL
BE SAME. LOW SIDE WILL BE TOP SIDE WHERE ALL CONDENSATE
COLLECTED THIS IS REFERENCE SIDE, NOW ON OTHER HAND HIGH
SIDE WILL BE LOWER, DIFFERENTIAL PRESSURE OBSERVED AT DPT.
LOWER SIDE WILL BE ALWAYS FULL IE FULL SCALE IF YOU ARE
HAVING TANK HEIGHT 1500 MM THEN PRESSURE AT LOWER SIDE IS
1500 MMWC. AND THAT OF HIGHER SIDE WILL BE THE ACTUAL WATER
INSIDE TANK WE SAY 500 MMWC STEAM PRESSURE WILL BE EVERY
WHERE SAME SO NO NEED TO CONSIDER PRESSURE INSIDE THE TANK.
MINUS AND PLUS WILL BE JUST FOR HAVING DIFFERENCE IN TWO
COLUMN IE HP AND LP. ALSO TANK IS NOT PRESSURIZED YOU CAN
USE PRESSURE TRANSMITTER CALIBRATED IN YOUR RANGE (HEIGHT OF
TANK MMWC)

Is This Answer Correct ?    6 Yes 4 No

Post New Answer

More Instrumentation Interview Questions

Name four general (not technical) criteria that would you consider important, when deciding upon a particular control valve?

1 Answers  


what is the diffrence between mmwc and kg/cm2 for pressure measurment when we are using mmwc and when kg/cm2 and why????? ?? what is the reason

19 Answers   Ecoboard, Jindal, Sepco,


difference between null and deflecting instrument.

5 Answers   ONGC,


What is the difference between PLC and DCS?

4 Answers   Honeywell,


Why the Proximitor supply should be Negative voltage? Why should not we give Positive voltage to the Transducer?

6 Answers   Moser Baer,






What for barriers are used in DCS & PLC systems?

2 Answers  


How does a strain gauge measure pressure?

2 Answers  


Can we use mov instead of esdv Explain the reason

1 Answers   KOC,


WHAT IS DIFFERANCE BETWEEN INSTRUMENT AND EQUIPMENT

1 Answers   Lupin,


in the boiler in the main steam line and its bypass line and the startup vent vales are only motorised valves why cant we use other types of valves such as pneumatic.

3 Answers  


how to convert cubic metre per hour to newton cubic metre per hour

0 Answers  


If the vibration probe near to the shaft,then output voltage will be decreased r increased?How?

1 Answers   Amtek, Hamsco, IJT,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)