Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


3element

Answers were Sorted based on User's Feedback



3element..

Answer / mazhar ali

IT IS BASICALLY TERMED AS 3 ELEMENT CONTROL.
THIS IS USED IN BOILER HOUSE WHERE IN DRUM LEVEL IS CONTROL.
SO IT INVOLVES FEED WATER CONTROL , STREAM FLOW CONTROL AND
DRUM LEVEL CONTROL SIMULTANEOUSLY.

Is This Answer Correct ?    8 Yes 0 No

3element..

Answer / sridhar

3 Element means,in that application is mostly used at
Boiler feed water control for maintaing the drum level in
steam drum,it consists 3 mesure devices,one is feed flow
trx,second is steam flow trx,and third one is drum level
(compensated)trx

Is This Answer Correct ?    5 Yes 0 No

Post New Answer

More Instrumentation Interview Questions

Can we calibrate an actuator?

5 Answers   Siemens,


tell me about Woodward505 Function as a point of Instrument Engineer.

4 Answers  


Guy's need your support,I want to measure closed tank level which is under vacuum -630mmHg using DP Transmitter, tank fluid density 1.38, Tank height is 7ft

4 Answers   icl,


tell about various protocols used in different plcs

3 Answers   Emerson, Samtel,


Why the tapping connections are taking above for gas service and below for liquid service?

2 Answers   ADCO,


what is the reset offset and control system in instrumentation

0 Answers   ABB,


You are looking at the RS-485-side of an RS-232/RS-485 converter and the power supply voltage for the converter is +5V. Under idle conditions (no transmission), and assuming you have enabled the RS-485 output: what would you expect at: (a) Output A measured against output B (b) Output A measured against ground (c) Output B measured against ground

1 Answers   EIT,


I wnat to practice more online type questions .so will you show them me to take a practice test?

1 Answers   VA Tech Wabag,


Why the Proximitor supply should be Negative voltage? Why should not we give Positive voltage to the Transducer?

6 Answers   Moser Baer,


What is the minmum distance between the electrical panel and Instrument panel

1 Answers   Dodsal,


what is PM/CM/RCM?

2 Answers   Emco,


Can u tell me the principle of the tc,rtd,level switch,pressure switch ,transmitter(pr flow level temp.),vibration...plz

0 Answers   Adani, SRF,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4456)
  • Electrical Engineering Interview Questions Electrical Engineering (16639)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)