In 120 m high RCC Chimney shell construction how we can calculate the inner an

In 120 m high RCC Chimney shell construction how we can
calculate the inner and outer dia of shell at every +1 m
level as this shell is inclined from bottom to top.

Question Posted / sachin

4 Answers
15307 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

In 120 m high RCC Chimney shell construction how we can calculate the inner and outer dia of shell..

Answer / sachin

BY CALCULATING THE SLOPE OF SHELL PER METER AND REDUCING
FROM OUTER AND INER DIA AT EVERY LEVEL WE CAN CALCULATE THE
ACTUAL DIA AT THAT STAGE.

Is This Answer Correct ?

14 Yes

2 No

In 120 m high RCC Chimney shell construction how we can calculate the inner and outer dia of shell..

Answer / n.c.kapri

in slipform technology ,we do a marking in spur beam from
center.drop the shawal from there and measure the distance
from inner wall to that marking,it will our I.D
ex:marking at 2.9m
distance from inner wall to that marking .475m
so inner dia =2.9+.475
=3.375m

now add the wall thikness in I.D & get outside dia

Is This Answer Correct ?

7 Yes

1 No

In 120 m high RCC Chimney shell construction how we can calculate the inner and outer dia of shell..

Answer / m.senthilkumar

(bottom outer dia- top outer dia)/ height=average reduce the
dia per 1mt
inner dia =outer dia is checked ok so just measurement wall
thickness is correct or not
example:
bottom outer dia=100mt top outer dia =82mt height=120mt wall
thickness=0.5mt
(100-82)/120=0.15mt each 1mt reduce the dia 0.15mt ok
+4m outer dia=(100-(4*.15))=99.40mt dia
+4m inner dia=(99.40-2*0.5(wall thickness)=98.40mt dia
chimney 90degree maintain =center point maintain 0 to 120mt&
check radius every +1mt

Is This Answer Correct ?

2 Yes

0 No

In 120 m high RCC Chimney shell construction how we can calculate the inner and outer dia of shell..

Answer / omkar

example:
bottom outer dia=100mt top outer dia =82mt height=120mt wall
thickness=0.5mt
(100-82)/120=0.15mt each 1mt reduce the dia 0.15mt ok
+4m outer dia=(100-(4*.15))=99.40mt dia
+4m inner dia=(99.40-2*0.5(wall thickness)=98.40mt dia
chimney 90degree maintain =center point maintain 0 to 120mt&
check radius every +1mt

Is This Answer Correct ?

1 Yes

1 No

Post New Answer

More Civil Engineering Interview Questions

concrete cube strength if fail 1 no in 7 days .What is the solution

8 Answers

what are co-efficient for jacks, acro spans and runners for slabs per sft?

1 Answers

what are the compressive strength requirements(in 7 days & 28 days) of cement sand mix used for plastering purpose (Cement:sand-1:6)? Kindly give the IS Code reference also.

3 Answers L&T,

how can i calculate pcc and rcc cu.mtr rate? specify labor and material cost should be diff

2 Answers

different type of beam

6 Answers L&T,

can i place column steel lapping in floor beam? my lapping is 24 inches in floor beam and 24 inches on floor beam

1 Answers

what is temp. control concrete and what use of it ?

1 Answers

contractor receive 100 MT steel.after compliting the work the contractor refund 90 MT steel.How reconsilation of steel done?

0 Answers

WHAT SHOULD BE THE THICKNESS OF CEMENT M-SAND MIXER IN BETWEEN TWO SOLID CEMENT BRICKS USED FOR A HOUSE WALL?

4 Answers

How much sand and cement requirement for 1 SQM 125mm thickness Brickwork

0 Answers

how to design paver block

1 Answers CCCL,

how to preaper for interview wat they asked in interview give me idea

0 Answers ONGC,

For more Civil Engineering Interview Questions Click Here