Interested to Buy Any Domain ? << Click Here >> for more details...
At which layer of the OSI model does the ping command operate?
A. session
B. network
C. transport
D. maintenance
- 12 Answers
- 47516 Views
- EF, IBM, jetking, Nexlinx, Rkd, TCS, Wipro, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / robert
ping operate in Network Layer only . Because it uses
ICMP....
| Is This Answer Correct ? | 106 Yes | 2 No |
Answer / m haja bahurudeen
Ans : B) Network
ping cmd using layer3. To check destination ip address.
| Is This Answer Correct ? | 34 Yes | 2 No |
Answer / yonten tshering
i think the correct answer will be network layer
| Is This Answer Correct ? | 17 Yes | 2 No |
Answer / mr.shahin07
Mr. M Haja Bahurudeen, Ur concept is little bit wrong.
Ping (Packet Internet Grouper) command is used to check the
remote host status,also used to self test the network
interface card of the computer, , not IP address. Ping
command use ICMP "Echo Request"& ICMP "Echo response"
message to perform its task.
| Is This Answer Correct ? | 13 Yes | 1 No |
Answer / nader alkahtani
Ping runs between layer 3 and 4 let us say layer 3.5
| Is This Answer Correct ? | 0 Yes | 0 No |
What is the Network Layer of the OSI responsible for? A.) Bridging B.) Routing packets through an internetwork C.) Regenerating the digital signal D.) Gateway services
What is the beaconing?
How many collision domains are in switch?
How we can find ASBR Router, we have no authentication to enter router?
Identify the command mode necessary to enter the standard ping command? A.) Router(config)# B.) Router> C.) Router(std-ping)# D.) Router(config-if)#
HI I am Rajveersinh. I am Leaving in Ahmedabad-gujarat. I am Hardware & Networking Stundent In JETKING. my Intersted in CICKO Side. Please send ME totel detail in CICKO surtifiction my E-mail ID IS as_raj@ymail.com
Which protocol gets a hardware address from a known IP address? A.) RARP B.) TCP C.) IP D.) BootP E.) ARP F.) ICMP
What is the difference between ‘bit rate’ and ‘baud rate’?
hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface
Cisco's implementation of ISDN BRI has multi protocol support, SNMP MIB support, and what other features? A.) Call waiting B.) Compression C.) ADSL D.) 1.544 Mbps E.) Call screening F.) Negative 'G' support
How signalling can be explained in D channel of ISDN?
Identify the command to configure the router to boot from an alternate IOS located in flash? A.) boot system flash IOS.exe B.) boot system tftp IOS.exe 172.16.5.1 C.) boot system alternate IOS.exe D.) boot system rom IOS.exe
CCNA 
