Axial force to keep the clutch in engaged position is provided by a) Springs arranged circumferentially b) Pressure plate c) Flywheel d) Clutch pedal
916The friction plate is always mounted on a) flywheel b) Pressure plate c) Internally splined hub d) Clutch spring
1019The main advantage of single plate clutch over cone clutch is a) Easier gear changing b) Less binding of contact surfaces c) Less pedal movement d) all of the above
1232The main function of transmission is a) To provide means to vary the torque ratio between the engine and the road wheels b) To provide neutral position c) To provide means to back the car d) all of the above
956The resistance to the vehicle motion whose magnitude remain constant with respect to the vehicle speed is a) Resistance due to gradient b) Resistance due to the road c) Resistance due to the tyre friction d) all of the above
852The resistance to the vehicle motion whose magnitude various with the square of the vehicle speed is a) Resistance due to gradient b) Resistance due to road c) Resistance due to the tyre friction d) Resistance due to wind
862If the tractive effort is the highest for a given velocity, then the vehicle must be in a) Top gear b) Third gear c) Second gear d) First gear
1507The point of interaction of the tractive effort curve and the total resistance curve is called a) Stabilizing speed point b) Low speed point c) High speed point d) Normal speed point
831If the given tractive effort curve and the total resistance curve does not intersect, then a) The vehicle will accelerate b) The vehicle will decelerate c) The vehicle will not be able to go at this gradient for the given gear d) None of the above
735The main disadvantage of sliding mesh type of gear box is a) High noise level b) Low mechanical efficiency c) High skill required by the driver d) all of the above
901Double declutching is used for the engagement of gears in a) Sliding mesh type of gear box b) Constant mesh type of gear box c) Synchromesh type of gear box d) None of the above
841High speed gear is obtained in the case of sliding mesh gear box when a) Motion is transferred through the clutch gear to lay shaft gear b) Main shaft is coupled to the clutch shaft c) Smallest gear on the lay shaft is engaged d) Largest gear on the lay shaft is engaged
896In case of a constant mesh gear box, when the left dog clutch is slid to the left by means of the selector mechanism, a) Direct gear is obtained b) First gear is obtained c) Second gear is obtained d) Reverse gear is obtained
845In a constant mesh gear box, when the right dog clutch is engaged with the gear on the right side of the main shaft, a) Direct gear is obtained b) First gear is obtained c) Second gear is obtained d) Reverse gear is obtained
806Post New Bosch Interview Questions
What are the attributes which can be used during the creation of a new angularjs directives?
Why is this loop always executing once?
What are the important principles of soa (service oriented architecture)?
How do I make multiple copies on one page in word?
How can you create a HDInsight Cluster in Azure?
MY generator water cooler inlet line height - 11 mtr inlet water line height - 7 mtr water come into the line from overhead tank, O/H tank height - 20 mtr the first tapping in the inlet line is 2" line which down to 4 mtr level plateform., second tapping in inlet water line goes to a pump 6" line installed at 4 mtr level plateform, pump capacity 200m3/hr, head- 30 mtr, hp-40. the outlet of pump of 6" water line connected to a header of 6 mtr long of 6" line, on this header the six tapping are connected, 4 nos. 3" line goes to 11 mtr height water cooler the pressure of the line is 0.15 to 0.25 kg/cm2, 2" and 4" pipe line connected to a cooler at 4 mtrlevel plateform. my question is, at 11 mtr height level the quantity of water and flow is not sufficient for my cooler, the temp. of cooler is rises much more. you are requested to suggest the modification of pipe line/ pump for take more water flow and pressure (desired pressure is 1 kg/cm2)
What is materialized view. What are different methods of refresh?
Can array grow dynamically in java?
send me few previous years section engineer question papers?..
What are the problems you faced while identifying an object in silk?
how to combine the transparent table with cluster table.
How can you avoid importing tables one-by-one when importing a large number of tables from a database?
What do you mean by append?
Is apache opensource?
If there is a pipe and you send it to a sub-contractor to be cut in to two or three pieces. How will you map such scenario in sap? Will you create separate material codes for each pipe with different length or what will be your approach?