why heat produced at junction of two different conductor.
what care should be taken to minimize it.
- 11 Answers
- 15142 Views
- Birla, Maihar Cement, I also Faced
- E-Mail Answers
Answer Posted / aziz_raghib2002
at the junction of the two conductors the conductors will
have different potential due to thier material
characteristics and thats why some P.D and so currentand
heat ie cu losses same material should be used and same
ch/hs material
| Is This Answer Correct ? | 1 Yes | 0 No |
Post New Answer View All Answers
if a.c supply is given to the motor,, what happen?
True or false question. 1.The fuse provide phase and neutral 2.power loss in electrical circuit can take place in (resistance or inductance or capacitance). 3.two phase system each phase has separated by a phase difference of (90 or 180 or 270 or 45). 4.3 phase balanced star connected load neutral current shall be (line current or phase current or zero or unity)
number of I/O devices in siemense plc
How u can give the overload setting to any motor protection relay for a HT motors with formula and Example?
why the frequency and voltage in india is 230v and 50HZ. when compared to USA say 110v and 60 HZ.
How many gap between finger contact in a.c.b. and v.cb.?
Post possible questions for Power Factor Panel FAT / SAT
What is fault clearing time for Current Limiting Moulded Case Circuit Breaker?.
how open delta PT works & what is its construction?
all the technical question with answers pleas send your email id ramar_eee@yahoo.com
how to set relay setting? and example calculation...
why we can use 1 to 5V dc
what is model question rrb junior engineer electrical gr.II
How dia computation perfomed in cold rolling mills .
TRAFO 1. WHY BREATHER IS USED. 2. WHY OIL GOES DOWN IN CONSERVATOR TANK. 3. WHY WE ARE TAKING OIL SAMPLE TAKING FROM BOTTOM OF TRANSFORMER. 4. HOW TO CHECK IR VALUE OF TRANSFORMER. 5. WHY OLTC HAVING BUCHHOLZ TRIP ONLY; WHY NO ALARM. 6. OFF LOAD TAP CHANGER OPERATION PROCEDURE. 7. TR. SHUTDOWN / ISOLATION PROCEDURE. 8. WHEN THREE TRS. IN PARALLEL, ONE TR. IS NOT SHARING THE LOAD – WHAT IS REASON AND WHAT YOU WILL DO. 9. WHY TR. HAS OLTC IN HV SIDE. 10. WHAT IS % IMPEDANCE. 11. WHY TR. RATING IN MVA. 12. WHAT IS VECTOR GROUP IN TR. 13. CONDITION FOR PARALLEL OPERATION OF TRS. 14. WHAT IS TERTIARY WINDING. WHERE IT WILL BE. 15. IF TR. TRIP ON BUCHHOLZ OR TAP CHANGER RELAY, WHAT YOU WILL DO. 16. DIFFERENCE BETWEEN OIL TEMP. AND WINDING TEMP. PROTECTION 17. HOW WINDING TEMP. IS MEASURED IN CAST RESIN TR. 18. DIFFERENT TYPES OF FAULTS IN TR. Trafo - Page-1 of 2 19. WHAT HAPPENS WHEN TR. CHARGED FROM LV. 20. WHAT WILL YOU DO IF MEGGER READING SHOWS ZERO BETWEEN LV WINDING AND EARTH. 21. CAN WE INTERCHANGE BUCHHOLZ RELAY OF MAIN TANK AND OLTC TANK. 22. IF THE LINE BETWEEN BREATHER AND CONSERVATOR TANK 23. LOCKED, WHAT WILL HAPPEN DURING LOAD CYCLE. 24. WHAT IS THE FUNCTION OF OIL SEAL IN BREATHER. 25. WHAT ARE LOCATIONS FOR BUCHHOLZ RELAY FIXED IN POWER TR. 26. WHAT ARE CHECKS IN POWER TR. DURING MAINTENANCE. 27. WHAT IS IMPORTANT WHEN WE CHECK OLTC OPERATION DURING MAINTENANCE. Trafo - Page 2 of 2
