what is DG synchronization panel
plz explain the working!!!!!!!
- 12 Answers
- 93653 Views
- Kirloskar, Lanco, MPS Techologies, Sedemac, I also Faced
- E-Mail Answers
Answer Posted / sandip g. kuvalekar
syncronizaing panel is used where one dg set syncronizaing
with two or more dg set when mains fail all dg start at a
time but after some time one will be on & other will be
stop as per load when load increased above 70% of the total
load the 2nd dg will be start & it syncronise with first
one & total load was distributed equally On that two dg set
& This process will go on
| Is This Answer Correct ? | 257 Yes | 39 No |
Post New Answer View All Answers
Whether amorphous core transformer is commercialized or not:Name of company making amorphous core transformer and what are different rating?
can anyone give an idea about dia calculation in cold rolling mill
A cable with concentric PE conductor must be used with frequency converter circuits what does its means.?
what is the power factor used by the PHCN in nigeria? 2. what is the difference between an alternator and generator. 3. Generation of poweris in KV but how is transmission is in MW. 4.If the transmission of power is 20,000MW how can it be increaesed to 80,000MW
what is die electric strnth of transformer ?
what is the difference between elcb and rccb ?
TRAFO 1. WHY BREATHER IS USED. 2. WHY OIL GOES DOWN IN CONSERVATOR TANK. 3. WHY WE ARE TAKING OIL SAMPLE TAKING FROM BOTTOM OF TRANSFORMER. 4. HOW TO CHECK IR VALUE OF TRANSFORMER. 5. WHY OLTC HAVING BUCHHOLZ TRIP ONLY; WHY NO ALARM. 6. OFF LOAD TAP CHANGER OPERATION PROCEDURE. 7. TR. SHUTDOWN / ISOLATION PROCEDURE. 8. WHEN THREE TRS. IN PARALLEL, ONE TR. IS NOT SHARING THE LOAD – WHAT IS REASON AND WHAT YOU WILL DO. 9. WHY TR. HAS OLTC IN HV SIDE. 10. WHAT IS % IMPEDANCE. 11. WHY TR. RATING IN MVA. 12. WHAT IS VECTOR GROUP IN TR. 13. CONDITION FOR PARALLEL OPERATION OF TRS. 14. WHAT IS TERTIARY WINDING. WHERE IT WILL BE. 15. IF TR. TRIP ON BUCHHOLZ OR TAP CHANGER RELAY, WHAT YOU WILL DO. 16. DIFFERENCE BETWEEN OIL TEMP. AND WINDING TEMP. PROTECTION 17. HOW WINDING TEMP. IS MEASURED IN CAST RESIN TR. 18. DIFFERENT TYPES OF FAULTS IN TR. Trafo - Page-1 of 2 19. WHAT HAPPENS WHEN TR. CHARGED FROM LV. 20. WHAT WILL YOU DO IF MEGGER READING SHOWS ZERO BETWEEN LV WINDING AND EARTH. 21. CAN WE INTERCHANGE BUCHHOLZ RELAY OF MAIN TANK AND OLTC TANK. 22. IF THE LINE BETWEEN BREATHER AND CONSERVATOR TANK 23. LOCKED, WHAT WILL HAPPEN DURING LOAD CYCLE. 24. WHAT IS THE FUNCTION OF OIL SEAL IN BREATHER. 25. WHAT ARE LOCATIONS FOR BUCHHOLZ RELAY FIXED IN POWER TR. 26. WHAT ARE CHECKS IN POWER TR. DURING MAINTENANCE. 27. WHAT IS IMPORTANT WHEN WE CHECK OLTC OPERATION DURING MAINTENANCE. Trafo - Page 2 of 2
Why have to use copper cable for local isolator to motor ?
Why front mounted CT polarities are always towards breaker?
1. How many types of mangers? 2.How many types of capacitors? 3.pls tell me normally types alternator problems?
WRITEDOWN FEW RELY CODES
1.what is the funtion of chiller primary & scondary pumps. 2.what is the use of distribution lines & Types. 3.what is the use the thermal power stations & how much capacity.
What is the principle of HIGH SPEED DIRECT DRIVE MOTOR ?
What is slope...? Explain slope 1 and slope 2...?
why the India electrical supply transmission loss is high when compare to us
