Why Batteries are rated as AH i.e AmpereHour,and its formula to converting Amp

Why Batteries are rated as AH i.e AmpereHour,and its
formula to converting AmpHour to Amp

Question Posted / husen

4 Answers
7817 Views
Suzlon, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Why Batteries are rated as AH i.e AmpereHour,and its formula to converting AmpHour to Amp..

Answer / prashant

whenever we switch on any appliance at that instants current
is the quantity that is been actually used. Batteries are
used to supply power hence forth their ratings are mentioned
in AH ( Ampere Hour ) i.e current capacity that can be
delivered in a period of 1 hour.you can divide Amp-hr by 60
to get amperes used in a minute.both are readings for
current only

Is This Answer Correct ?

12 Yes

4 No

Why Batteries are rated as AH i.e AmpereHour,and its formula to converting AmpHour to Amp..

Answer / fakhir

A battery can deliver the power for limited time period.
Battery rating in AH reflects its capability to supply X
amps in a period of one hour. Operational time of a battery
thus can be extended in proportion to amps loading i-e
lower the connected load higher the service time. Thus
expressing capacity in absolute 'amps' does not make
sense.

Is This Answer Correct ?

4 Yes

2 No

Why Batteries are rated as AH i.e AmpereHour,and its formula to converting AmpHour to Amp..

Answer / sunil kaushik

amp-hour is means that a battery can supply toatl ahr for 20 hrs .so by dividing the amps with hous we can get the a/hr.

i do not why this is use

Is This Answer Correct ?

1 Yes

3 No

Why Batteries are rated as AH i.e AmpereHour,and its formula to converting AmpHour to Amp..

Answer / venkatesan.j

It reflets how much current it can supply for own hour, but
if reduced current is drawn then the time period it can
supply is obtained dividing the AH by current drawn.

Is This Answer Correct ?

0 Yes

4 No

Post New Answer

More Electrical Engineering Interview Questions

what precautions to be taken while desigining a LT,HT panel. Eg-LT panel PCC panel with ACB installed. HT panel VCB panel with VCB installed. & what is main diffrence betwn IP54 & IP55 construction of panel.

0 Answers Bhel,

What is the difference between Dielectric and Insulator

9 Answers

Why PT is fitted in incomer panel.....?

1 Answers

is it possible to start a motor in felid connected to a remote mcc

0 Answers BIET,

Is a d.c.compound motor is use as a booster? how?

0 Answers

What is the importance of counter based plan & how is it scheduled?

0 Answers TATA,

Please provided formula for calculate the cable size from step up transformer to M.V panel, run overhead aluminum cables, total load is 5mega watt, total length 900 feet.

0 Answers SK Engineering,

the site measured knee point voltage of protection class CTs should be greater than rated knee point voltage? what about meetering class CTs. Should it be below the rated knee point voltage?

0 Answers

Conventionally, capacitors are considered to generate reactive power and inductors to consume it,how??????

1 Answers

how to calculate the surge level of surge suppressors related to the SF6 cicuit breakers?

0 Answers Crompton Greaves,

how a resistor resists to flow the current?how an inductor oppses the sudden change in current?how a capacitor opposes a DC voltage.

0 Answers Hindustan Unilever Limited,

depletion layer will form beforre biase or after bias ?

2 Answers

For more Electrical Engineering Interview Questions Click Here