how is classified voltage level in generation,transmission & distribution

Categories >> Engineering >> Electrical Engineering
Suggest New Category

how is classified voltage level in generation,transmission
& distribution system?,

Question Posted / gtmanikandan

7 Answers
9752 Views
Adani, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

how is classified voltage level in generation,transmission & distribution system?,..

Answer / sukhvinder

distrbution 415 v
gen 11kv
trans 33-765 kv

Is This Answer Correct ?

22 Yes

2 No

how is classified voltage level in generation,transmission & distribution system?,..

Answer / kannu

generation:11-16.5kv
transmission :132-765kv
distribution: 230v,415v

Is This Answer Correct ?

14 Yes

2 No

how is classified voltage level in generation,transmission & distribution system?,..

Answer / ramanjaneyulu

genaration:11kv

transmission: 400kv-33kv

distribution:11kv-415,230v

Is This Answer Correct ?

3 Yes

0 No

how is classified voltage level in generation,transmission & distribution system?,..

Answer / prashant

the above ans is write though i wud like to add 230 V i the
distribution

Is This Answer Correct ?

8 Yes

6 No

how is classified voltage level in generation,transmission & distribution system?,..

Answer / arul

Generation : 11kv
Distribution. : 440v: 240v
Transmission:440kv ; 33kv; 765kv

Is This Answer Correct ?

0 Yes

0 No

how is classified voltage level in generation,transmission & distribution system?,..

Answer / azarudeen

Generation : 11 KV - 20 KV(20 KV for 600 MW generator)
Transmission : 33 KV - 765 KV(765 KV is DC)
Distribution : 230V - 33 KV

Is This Answer Correct ?

2 Yes

3 No

how is classified voltage level in generation,transmission & distribution system?,..

Answer / nagarjunacharya

gen 11kv-16.5kv tXssion33kv765kv distribution 33kv-
22ov

Is This Answer Correct ?

0 Yes

2 No

Post New Answer

More Electrical Engineering Interview Questions

what is the different between bus section and bus coupler

1 Answers

If AVR fails in DG set what will be the affect?

17 Answers GoodYear, Hotline Glass, HSL,

I am using submission of two ct in one and half scheme for 67/67N protection. Both CTs star point is grounded separately near ct box.Will two point ground give wrong tripping to 67/67N during fault or no matter.

0 Answers NCC,

what is allowed value of zero sequence impedancce of 6.6 kv nuetral earthing transformer ?what is the actual value

0 Answers

What is a HRC fuse (Full form)

26 Answers Gammon, HRC, Moser Baer,

What is the phase relationship between the primary and secondary voltages of a transformer?

0 Answers

suppose i have two single and three phase induction motor,thier have not any rating on its panel,anybody can tell me which motor is single or three phase?

1 Answers Doon,

why Line voltage =1.732XPhase voltage what mean by 1.732

4 Answers IBM, NCC,

What is rated value? is it phase values or line values?

1 Answers

how to compute kvar in substation feeder to improve power factor and sending voltage

0 Answers

Whether IP65 enclosure box blocks ventilation if driver for LED have to enclosed inside IP65 box

0 Answers Siemens,

phase association of 3PH L&T static CT meter is wrong. means 1PH & 1 CT connected properly and other 2 voltage and CT's inter changed. what would be the impact in the reading?

3 Answers KSEB,

For more Electrical Engineering Interview Questions Click Here