Explain what type of flow measurement devices is best for slurries?
No Answer is Posted For this Question
Be the First to Post Answer
What are the various utilities of the process plant?
What are the effects of oils on the properties of Polyolefins?
What is the basic difference between dispersion & distribution in any polymer blend or alloy??
ENGINEERING MATERIAL - EXAMPLE 12.1 : In crystal material, hexagonal crystal system could form 4-digit index in certain direction of solid. For [1(-1)0] direction in the hexagonal crystal systems of particular catalyst applied in fume removal of incinerator, what is the four-digit index for this direction? Hint : The transformation equations between the 3-digit [h'k'l'] and the 4-digit [hkil] indices are : h = (1/3) (2h'-k'); i = - (h + k); k = (1/3) (2k'-h'); l = l' A. [(-1)100] B. [1(-1)00] C. [(-1)000] D. [00(-1)(-1)] E. [(-1)0(-1)0]
Question 42 - According to Margules Equation, P = x(1) p(1) g(1) + x(2) p(2) g(2) for a two-component mixture where P is bubble pressure, x is mole fraction, p is saturation pressure, g is constant given by ln g(1) = x(2) A x(2). Find the value of A as a constant when P = 1.08 bar, p(1) = 0.82 bar, p(2) = 1.93 bar in a 50 : 50 mole fraction mixture. Estimate the pressure required to completely liquefy the 30 : 70 mixture using the same equation, by proving P = 1.39 bar. Take note that ln g(2) = x(1) A x(1), ln g(1) = x(2) A x(2).
diffirance between heat transfer & thermodynamics
3 Answers Shinsung Petrochemicals,
Question 58 – In the design of a solar power system steps of calculations below are followed : (a) The power output of the inverter of the of the solar panel is 100 watts. What is the power input, Pin to the inverter when the efficiency of the inverter is 50 %? (b) If the rated power of the inverter is 300 watts, how many inverter is needed for the solar panel? (c) Charge controller of V = 12 volts is used to supply power to the inverter. What is the input current I to the inverter? (d) If the charge controller capacity is 10 A, how many charge controllers are needed? (e) If a biochemical mixer consumes 100 watts, running for 2 hours per day, what is the energy consumption in kilowatt hour per day? (f) What is the input energy needed when the efficiency of the inverter is 50 %? (g) If your area receives 2.88 hours of full sunlight per day, how much energy, in kilowatt hour can be produced per day when one solar panel can produce 20 watts of power? (h) If you know that you have to produce total energy as the answer for (f), how many solar panels are needed? (i) Each V = 12 V battery has 5 ampere hours. If the total energy needed is in answer (f), then how many batteries are needed to run the biochemical mixer if without sunlight for 3 days?
In differential centrifugation of cells with diameter D in centimeter, the square of D is given by D x D = [18n ln (RF / RI) ] / [ (RP – RFF) Wt ] where n is the fluid viscosity (poise), RF is the final radius of rotation (cm), RI is the initial radius of rotation (cm), RP is cell density (g/ml), RFF is the fluid density (g/ml), W the square for the rotational velocity in (radians / s) (radians / s), t is the time required to sediment from RI to RF (s). Derive an equation for W as a function for D, n, RF, RI, RP, RFF and t, with the stated units above, in radian
Question 29 – For a Vernier scale that consists of 0.11 cm per section, estimate the length on actual standard ruler of 0.1 cm per section for 2.39 m and 0.91 m.
pls send me HPCL & reliance test paper for chemical engineering.....
For what ration of Lengh/Dia. of tank (Jacketed tank), maximum heat transfer area is available?
MICROBIOLOGICAL ENGINEERING - QUESTION 28.3 : In the calculation of the growth of bacteria, absorbance, A in spectrophotometry is used. According to Beer-Lambert Law, A = e x l x c where A is the absorbance of the solution (no unit), l is the distance of light travels through the solution (in cm), e is the molar absorptivity or the molar extinction coefficient [ in L / (mol.cm) ]. For a particular solute and fixed path length : As / Ao = Cs / Co where Ao is the observed signal for a known concentration Co, and As is the observed signal for a sample concentration Cs. (a) For a cell concentration of 560 cells / mL, a spectrophotometre gives an absorbance reading of 1.0. A mixture of concentration 3600000 cells / mL can be diluted in several operations, with each operation having a dilution of 1:20. How many dilutions should be made so that the concentration of this mixture can be calculated within a range of A = 0.0 to 1.0. (b) In another experiment, a sample tube of 1 cm in width is used. Let A = 0.06 and e = 0.0012 ml / (cell.cm). Find the cell concentration of the sample.