Utilizing RIP, what is the limit when it comes to the number of hops?
- 0 Answers
- 799 Views
- I also Faced
- E-Mail Answers
No Answer is Posted For this Question
Be the First to Post Answer
Identify 3 characteristics of switches? A.) Increase available bandwidth B.) Decrease broadcast traffic C.) Support full duplex in a multipoint topology D.) Make fowarding decision using MAC address E.) Create collision domains
hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface
Identify 2 transport layer protocols? A.) IP B.) TCP C.) CDP D.) ARP E.) UDP
mention the funtions about connection oriented and connectionless protocol and how it works ?
Tell me which cable we connect in db-9?
What is the advantage of vlan?
What is a characteristic of Store and Forward switches? A.) They forward the frame before it is completely read. B.) They work at wire speed. C.) They are the same a Cut-Through switching. D.) They read the entire frame and check CRC before forwarding. E.) They decrease latency.
What is the difference between an igp and an egp?
To monitor IP igrp traffic, you can use "debug IP igrp transaction" or "debug IP igrp events". How do you display information about IPX routing update packets? A. debug routing B. debug ipx transaction C. debug ipx routing activity D. debug ipx events
hi friends i am jitendera kumar sinha.i have a question in mind that what is the diffrence between router and l3 switch i serched on google and found that switch L3 is best in lan and router are best in wan and switch are more faster then router.beside that any short of technical diffrence if you body know then plz plz and plz reply. my 2nd question is that why we canot replace router with L3 switches (donot tell that it is costly then router).i want any technical cause. this is 1 am hope in noon when ever i logg again i will find the answer posted by you. thanks onse again plz pzl make reply thanks jitendera kumar sinha jitenerasinha.it@gmail.com
Identify the components in the following command 'interface serial0/1/1' A.) Serial interface, port number 0, slot 1, port adapter 1 B.) Serial interface, slot 1, port number 1, port adapter 0 C.) Serial interface, slot 0, port adapter 1, port number 1
What is a characteristic of Store and Forward switches? A.) They work at wire speed. B.) They are the same as Cut-Through switching in 'prune' mode. C.) They forward based on transport layer info. D.) They forward the frame before it is completely read. E.) They increase latency.
CCNA 
