What is full form of G.O.D in 11kv distribution?

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / deepakvarma

9 Answers
74502 Views
GOD, MSEB, Shyam Indus Power, STL, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What is full form of G.O.D in 11kv distribution?..

Answer / jackblade76

Gang Operated Device

Is This Answer Correct ?

185 Yes

26 No

What is full form of G.O.D in 11kv distribution?..

Answer / anantha murthy manja

It is Group Operating / Gang Operating Device. Both are correct.

Is This Answer Correct ?

75 Yes

16 No

What is full form of G.O.D in 11kv distribution?..

Answer / nagesh.patwari

It's Gang Operated Device, It is a most commonly used switch in small to medium substations, Pole mounted Substations is a gang-operated, air-break disconnect switch.

The “Gang” refers to the three phases being electrically or mechanically tied together so that the 3 phases open at the same time. The “Air Break” refers to a visible break in the air that allows crews to see that the switch is truly open.

Is This Answer Correct ?

14 Yes

0 No

What is full form of G.O.D in 11kv distribution?..

Answer / bhupatmeer

Gange operated divice

Is This Answer Correct ?

9 Yes

1 No

What is full form of G.O.D in 11kv distribution?..

Answer / shailesh vasava

Gang operated disconnector

Is This Answer Correct ?

3 Yes

2 No

What is full form of G.O.D in 11kv distribution?..

Answer / krunal jariwala

WHY WE NOT GIVE DC SUPPLY IN X'MER PRIMARY SIDE

Is This Answer Correct ?

17 Yes

17 No

What is full form of G.O.D in 11kv distribution?..

Answer / nisha

Good question And improve future thank you

Is This Answer Correct ?

0 Yes

0 No

What is full form of G.O.D in 11kv distribution?..

Answer / sandeep kumar badal

GOD stands for.....
G : Generator
O : Operator
D : Destroyer

Is This Answer Correct ?

48 Yes

54 No

What is full form of G.O.D in 11kv distribution?..

Answer / jignesh doshi

gradually operated device

Is This Answer Correct ?

22 Yes

43 No

Post New Answer

More Electrical Engineering Interview Questions

a)In a 3-phase 4-wire circuit, a circuit breaker is selected to protect the circuit whose highest fault level is 6.6 MVA. Determine the required minimum breaking capacity in kA. (Note: Covert 3-phase power in terms of kA to find answer.) b)Using the below, determine the required minimum making capacity in kA as a “peak value”. Rate breaking capacity (Icn) ka: Icn<= 1.5 Factor = 1.41 1.5

0 Answers

How to calculate total harmonic distortion level(THD) in VFD? and how can we reduce harmonics?

0 Answers Apollo,

what is the principle of the single phase energy meter? and,what is the advantages and disadvantages of single phase energy meter?

0 Answers

How to calculate that clean water supply in one Day from 150 KLD STP?

0 Answers

Give 3 phase transformer connections for 24 pulse rectifier using thyristors.

0 Answers

How the size of transformer decreases if we increases the frequency?

2 Answers

what are the major difference between 3phase 3wire and 3phase 4wire trivector meter?

2 Answers L&T, NTPC,

What is mean by CT Saturate? how do we calculate?

5 Answers ABC,

what happen for input voltage output voltage input current output current and kva if we increase primery winding in transformer?

1 Answers

what is th basic difference between a d latch time line and a d flip flop time line???

0 Answers

If we have two nodes A and B and Vab is the potential difference between these nodes then which node is called reference node a.node A b.node B c. Ground node

1 Answers

how does directional relay work incase of ac ?

0 Answers

For more Electrical Engineering Interview Questions Click Here