Answer / masthan

types of bus bar -
1. rigid type
2. strain type
Busbar arrangements -
1.Single Busbar system
2.single busbar system with sctionalisation.
3.double busbar system with single breaker.
4.double busbar system with double breaker.
5.breaker and half scheme with two main buses.
6.main and transfer busbar scheme.
7.double busbar with bybass isolator.
8.mesh scheme (ring bus)

Answer / md. shahin azad

An aluminum or copper conductor supported by insulators
that interconnects the loads and the sources of electric
power in an electric power system. A typical application is
the interconnection of the incoming and outgoing
transmission lines and transformers at an electrical
substation. Bus-bars also interconnect the generator and
the main transformers in a power plant. In an industrial
plant such as an aluminum smelter, large bus-bars supply
several tens of thousands of amperes to the electrolytic
process. See also Electric power substation.


major types of bus bar
(1) Rigid bus-bars, used at low, medium, and high voltage

The rigid bus-bar is an aluminum or copper bar, which is
supported by porcelain insulators.

(2) Strain bus-bars, used mainly for high voltage

The strain bus-bar is a flexible, stranded conductor which
is strung between substation metal structures and held by
suspension-type insulators.

(3) Insulated-phase bus-bars, used at medium voltage

The insulated-phase bus-bar is a rigid bar supported by
insulators and covered by a grounded metal shield. The main
advantage of this system is the elimination of short
circuits between adjacent phases.

(4) Sulfur hexafluoride (SF6)-insulated bus-bars, used
in medium- and high-voltage systems

The sulfur hexafluoride-insulated bus-bar is a rigid
aluminum tube, supported by insulators and installed in a
larger metal tube, which is filled with high-pressure
sulfur hexafluoride gas.

According to size 3 types

* tubular bus bar
* solid bus bar
* flat bus bar

According to capacity 4 type

* Extra high voltage bus
* high voltage bus
* medium voltage bus
* low voltage bus

different between electrical and electronics Engineering????

4 Answers  

---

In our factory there is one no. of Series trip HT 6KV OCB. 1. Is it possible to measure CT out put current by 440V Clamp meter? The measurement is required for knowing the exact value of current in CT secondary to set up protection for transformers. 2. plase forward the single line diagram of AMF panel?

1 Answers   HAL,

---

how much percentage(%) of load can feed in power transformer?

1 Answers   Siemens,

---

AL=0B9H,bl=75H, ADD AL,BL AL=____________? CF________? OF___________?

0 Answers  

---

In Air circuit breaker LSIG protection unit is used. Without fault in cables (2 runs 3Cx150Sq.mm Copper, 1Kv grade, XPLE armored cable IR value is more than 550Mohm @ 500V Megger) and load section Long time Overcurrent protection is triggers and trips the unit. We changed LSIG protection with new factory tested unit. Even then fault is persisting. Please suggest the possible causes

0 Answers  

---

i am swathi, b.tech 4th year. In smps(switched mode power supply)we are using diodes,mosfets,igbts for controling of current. And my question is why we did not use thyristors(scr)? it is also act as a switch,then what is the drawback of scr as compared to above transisters> if we use the scr,then what is happening ? plz give reply as soon as possible bcoz i am doing project on smps. plz frnds i want ans for that. if anybody know the ans plz send to my e-mail id /swathi.tadakapally@gmail.com/

5 Answers   EEE, TCS,

---

Dyn1 transformer vector group testing how to do

0 Answers  

---

What is the difference between Class PX & Class X CT's

2 Answers   ABB,

---

What is the permissible value of earth resistance!

11 Answers   Torrent Power,

---

What is the one main difference between ups & inverter ? And electrical engineering & electronics engineering ?

0 Answers  

---

what is high voltage in india?

11 Answers   Essar,

---

What is the meaning of 'A synchronous motor floating on line'?

2 Answers  

---