Answer / jagannath gudia

d

Answer / guest

Answer: D

The Cisco HDLC frame format is Flag, Address, Control
Proprietary, Data,

FCS, Flag. The PPP frame format is Flag, Address, Control,
Protocol, LCP

(Code, Identifier, Length, Data), FCS, Flag. The SDLC and
LAPB format is

Flag, Address, Control, Data, FCS, Flag.

What is the command for change serial cost?

0 Answers  

---

Identify the IPX standard access-list number range? A.) 600 - 699 B.) 1000 - 1099 C.) 1 - 99 D.) 100 - 199 E.) 800 - 899

1 Answers  

---

What command can be used to test IPX connectivity? A.) Ping 2e.000.0045.8923 B.) Ping 192.168.100.1 C.) Ping ipx 2e.0000.0045.8923 D.) Ipx ping 2e.0000.0045.8923

4 Answers  

---

Which protocol will let neighbor routers know if your internetwork experienced congestion on a serial port? A.) BootP B.) IP C.) ICMP D.) ARP E.) FTP F.) RARP

1 Answers  

---

What is the purpose of the DLCI? A.) Identifies the remote routers B.) Contained with a 802.2 frame for routing purposes C.) Used with PPP during authentication D.) Identifies the PVC in a Frame Relay network

1 Answers  

---

---

On an ISDN BRI interface, the control channel is the 'D' channel. What is the rate of this channel? A.) 64 Kbps B.) 1.544 Mbps C.) 128 Kbps D.) 2.048 Mbps E.) 16 Kbps

2 Answers  

---

Which command would show all Ethernet interfaces with IPX configured on them? A.) show interface ipx ethernet B.) show ipx interface C.) show ipx interface ethernet D.) show ipx E.) show version F.) show run

1 Answers  

---

You have an IP host address of 201.222.5.121 and a subnet mask of 255.255.255.248. What is the broadcast address? A. 201.222.5.127 B. 201.222.5.120 C. 201.222.5.121 D. 201.222.5.122

1 Answers  

---

What information is provided by the local management interface (LMI)? A.) LMI encapsulation type B.) The current DLCI values C.) The status of virtual circuits D.) The global or local significance of the DLCI values

2 Answers  

---

Which command displays the IPX SAP table? A.) show ipx sap B.) show sap C.) show ipx interface D.) show ipx servers E.) show ipx

1 Answers  

---

As the system administrator, you enter the following commands at the command prompt: ipx routing access-list 800 permit 2b 4d int e0 ipx network 4d ipx access-group 800 out int e1 ipx network 2b int e2 ipx network 3c What did these command accomplish? A. Traffic from network 4c destined for network 4d will be forwarded out Ethernet0. B. Traffic from network 3c destined for network 4d will be forwarded out Ethernet0. C. Traffic from network 2b destined for network 4d will be forwarded out Ethernet0. D. Traffic from network 4d destined for network 2d will be forwarded out Ethernet0.

1 Answers  

---

Which of the following is a characteristic of a switch, but not of a repeater? A.) Switches forward packets based on the IPX or IP address in the frame B.) Switches forward packets based on the IP address in the frame C.) Switches forward packets based on the MAC address in the frame D.) Switches forward packets based only on the IP address in the packet

2 Answers  

---